Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool Apparel Printer film not feeding, dropping, or "Printer film jam" with the OS1 oven
If the film will not move at all, the pinch roller switch is usually not pressed fully down. If the film reaches the OS1 oven but jams, drops into the buffer, or throws Printer film jam (checkByEncoder or filmJam2), the cause is usually powder on the jam sensor, film loaded crooked or touching the white guideline, or the alignment calibration. Clear any real jam, clean the sensor, reload the film straight, and recalibrate.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Film does not move when printing, or Feed/Eject does nothing | Pinch roller switch not engaged | Steps 1 to 3 |
| Film moves in jerks or the wrong way | Loose pinch roller shaft or bearing, or motor cable | Step 3 |
| Clicking or crunching from the oven, film stuck inside | Real jam | Step 4 |
| Printer film jam error, but no film is stuck | Dusty jam sensor, crooked film, calibration | Steps 5 to 8 |
| Film falls into the buffer instead of entering the oven | Uneven film end, alignment, calibration | Steps 6 to 8 |
Step by step
-
Press the pinch roller switch fully down
Open the lid and find the pinch roller switch on the right side of the roller assembly. Press it down until it clicks into the locked position.
-
Do the pull test
With the switch down, gently push and pull the film by hand. If it slides freely, the rollers are not gripping: press each roller down firmly so it sits flat on the film. If the film is held tight, move on.
-
Watch the shaft under the film
On the LCD, go to Maintenance > Control and hold Feed or Eject while you watch the pinch roller shaft under the film. If a bearing has come off the end of the shaft, or the shaft does not turn, stop and contact us. The remaining fixes involve parts and opening the rear panel.
-
Clear a real jam
In xTool Studio, go to Device settings > Accessory information > Film material control and click Feed to push the film out of the delivery slot. If that fails, let the OS1 cool completely, then open the maintenance door and remove the film by hand. Close the sliding door first, then the maintenance door.
-
Clean the jam sensor
Slide out the OS1's used powder bin to reach the film jam sensor, and brush it clean with the brush from the package. Refit the bin and try again. Powder buildup here is a common cause of false jam errors.
-
Reload the film straight
Roll the film up so both edges are even. Leave only a short piece inside the printer, then pull it out from the middle so it sits square.
-
Check the gap at the white line
The film edge must not overlap the white marking line. Leave about 0.5 mm between them.
-
Run the film alignment calibration
Follow xTool's Film Alignment Calibration for the Apparel Printer and OS1. During calibration, the front of the film should stop within the thick marking line. If it still misfeeds, xTool has a reset for the calibration value that needs recent firmware and your serial number; contact us and we will walk you through it.
Send us this if it keeps happening
- A photo of the film next to the white line
- A photo of where the film stops during calibration
- A short video of the jam, the calibration value, firmware version and serial number
Text them to (562) 609-4996.
Watch xTool's video: Troubleshoot paper feed detection failure
More videos
Embedded from the manufacturer's official channel.
Common questions
What do the error codes checkByEncoder and filmJam2 mean?
Both appear as Printer film jam. xTool says they can be a real jam or a false alarm caused by a dirty sensor, crooked film or a wrong calibration value.
Can I pull jammed film out of a hot oven?
Let the OS1 cool completely first. Then try the Feed button, and only open the maintenance door to remove film by hand if that fails.
How far from the white line should the film edge be?
xTool says leave about 0.5 mm between the film and the white marking line. The film must not overlap the line.
Does other brands' film cause this?
It can. xTool recommends only its own PET film for the Apparel Printer.
- Troubleshoot Film Not Feeding During Printing
- Troubleshooting: Film Not Feeding or Ejecting Properly
- Troubleshoot "Printer Film Jam" Exception
- Apparel Printer and OS1 Troubleshooting: PET Film Not Feeding into Oven
- AA support requests about xTool Apparel Printer film feeding, 2024 to 2026










































































