Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool OS1 Automatic Shaker Oven support
The xTool OS1 powders, shakes and cures transfers coming off the xTool Apparel Printer, and you control it from the printer's touch panel. Preheat it before every session, keep it connected to an air purifier, and brush the film detection sensor every day. Most errors and curing problems come back to powder on the sensors, a skipped preheat, or the room being too cold or too humid.

Setup & first print
Daily & weekly maintenance
Troubleshooting
- xTool Apparel Printer and OS1 transfers peeling, cracking or creased: heat press settings and techniqueFor xTool PET film on 100% cotton, xTool recommends 160°C (320°F) for 6 seconds, peeling only after the transfer cools...
- xTool Apparel Printer film not feeding, dropping, or "Printer film jam" with the OS1 ovenIf the film will not move at all, the pinch roller switch is usually not pressed fully down. If the...
- xTool OS1 errors: Misalignment, printer not recognizing the oven, and oven won't power onFor a Misalignment error, trim and realign the film, brush the film detection sensor, restart both machines and run Device...
- xTool OS1 powder not curing: powdery, patchy, yellow or oily transfers and how to fix themIf transfers come out of the OS1 powdery, check the curing temperature (xTool recommends 110°C, 230°F), preheat until the panel...
Error messages
- xTool Apparel Printer film not feeding, dropping, or "Printer film jam" with the OS1 ovenIf the film will not move at all, the pinch roller switch is usually not pressed fully down. If the...
- xTool OS1 errors: Misalignment, printer not recognizing the oven, and oven won't power onFor a Misalignment error, trim and realign the film, brush the film detection sensor, restart both machines and run Device...
Techniques & settings
Manuals & downloads
Watch xTool's video: OS1 Automatic Shaker Oven unboxing and first use
More videos
Embedded from the manufacturer's official channel.
About the xTool OS1 Automatic Shaker Oven
The xTool OS1 Automatic Shaker Oven is the powder and curing stage for the xTool Apparel Printer and Apparel Printer Plus. The printer sits on top of the OS1 and is screwed to it. Printed film drops into the oven, gets coated with hot-melt adhesive powder, is shaken, cured and delivered as a finished transfer. The OS1 has no screen of its own: you run it from the printer's touch panel by tapping the temperature icon, or from xTool Studio.
Maintenance at a glance
| How often | What to do |
|---|---|
| Daily, before use | Brush the film detection sensor clean |
| Weekly | Clean the powder-shaking motion sensor and the delivery slot, and empty the waste-powder bin |
| Monthly or when full | Clean the film output detection sensor and empty the glycerin container |
| As needed | Clean the inspection window, the film fork-lifter and the powder bin area |
| Every session | Preheat and wait for the Stable icon before printing |
Wear nitrile gloves and use the brush that came in the box. Turn the oven off and let it cool before you open the maintenance door.
Where to put it
xTool gets the best curing at 20 to 30°C (68 to 86°F) and 45 to 60% relative humidity. Keep it out of direct sunlight, which can confuse the sensors, and away from air-conditioning vents and fans blowing on the film output. Leave at least 1 m (40 in) behind it and 90 cm (35 in) on each side for daily use and maintenance. The oven must run with an air purifier: xTool recommends the SafetyPro AP2 on Auto or Level 2, with the exhaust pipe fully stretched out.










































































