Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool OS1 powder not curing: powdery, patchy, yellow or oily transfers and how to fix them
If transfers come out of the OS1 powdery, check the curing temperature (xTool recommends 110°C, 230°F), preheat until the panel shows Stable, and keep drafts and cold air off the oven. If only later jobs fail, add queued jobs before the previous film enters the oven. Yellow powder means too hot, and an oily, pitted print means too cool: adjust 5°C at a time.
A properly cured transfer has the powder fully melted into an even, slightly textured "orange peel" surface. If you see loose, powdery or patchy areas, the powder did not cure. xTool splits the problem into two patterns.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Every transfer powdery, even the first | Temperature too low, no preheat, cold room or drafts | Pattern A |
| First job fine, later jobs powdery | Oven temperature dipping between jobs | Pattern B |
| Powder turned yellow | Oven too hot | Other curing problems |
| Pressed design looks oily or pitted | Ink not fully dried in the oven | Other curing problems |
| Smoke or a strong smell | Fumes not being purified | Other curing problems |
Pattern A: it never cures properly
-
Check the temperature setting
xTool's curing guide recommends 110°C (230°F). Tap the temperature icon on the printer panel to see and change it. If you are already at 110°C, raise it 5°C (9°F) at a time and check a transfer after each change.
-
Preheat and wait for Stable
Tap the temperature icon, then Preheat > Start up. Do not print until the Heating icon changes to Stable (temperature holding within 2°C).
-
Check the room
xTool's ideal room is 20 to 30°C (68 to 86°F) at 45 to 60% humidity. Look for air conditioning or a fan blowing on the film output area, or a very cold shop. Move the oven out of the draft or to a steadier spot, and keep space around it so it holds its heat.
Pattern B: the first job cures, the next ones don't
-
Preheat to Stable before each job
Check the icon is Stable, not Heating, before you send the next job.
-
Time your queue
The Apparel Printer can queue jobs. Add the next job before the previous one enters the oven. If a job is already curing, wait until it finishes before you add more. Queued jobs run in the order they were created.
Other curing problems
- Yellow powder after curing: the oven is too hot. Lower the curing temperature 5°C (9°F) at a time until it stops.
- Oily or pitted surface after pressing: the curing temperature was too low and the ink did not fully dry. Raise it in 5°C steps until the oily look and dents go away.
- Smoke or odor while curing: the exhaust is not being cleaned. Connect an air purifier (xTool recommends the SafetyPro AP2 on Auto or Level 2) and keep the exhaust pipe fully stretched out. A third-party purifier must move 120 m³/h; the wrong airflow also hurts curing.
- Thin unprinted lines at even spacing: marks from the pressure rollers, usually from high humidity. Get the room back into range and wipe damp pinch rollers with a lint-free cloth.
- A blank patch only at the very start of a new roll: the sticker that holds the roll closed can lift the film coating. It only affects the first few inches; keep printing.
Cured film does not keep forever. xTool says about 7 days, less in humid areas. Store transfers sealed in a bag, in a dark dry place, with a desiccant packet for longer storage.
Still curing badly after all of this? Text us a photo of a transfer and of the panel temperature at (562) 609-4996.
Common questions
What temperature should the OS1 run at?
xTool's curing troubleshooting guide recommends 110°C (230°F) as the starting setting, adjusted in 5°C steps from there.
Why does only the first job cure?
The oven loses heat between jobs. Make sure it shows Stable and add new jobs before the previous film reaches the oven.
Can a fan near the oven really matter?
Yes. xTool lists air conditioning or fans blowing on the film output as a cause of curing failure.
How long can I keep cured transfers?
About 7 days per xTool, less in humid conditions. Seal them in a bag in a dark, dry place.











































































