Support
Machine type
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4) support

Covers: L2 · XL2 · XL2 Pro · XL3 · XL4

Everything for keeping a DTF Station Prestige L2, XL2, XL2 Pro, XL3 or XL4 printing: the morning and evening routine, weekly cleaning, fixes for clogs, weak white, film feeding and alignment problems, and the setup resources for each model. The five machines share most procedures. The main differences are the number of print heads, the ink set, and whether the white caps are wetted by hand (L2, XL2) or automatically (XL2 Pro, XL3, XL4).

DTF Station Prestige XL4 roll-to-roll DTF printer on its stand, three-quarter view

Setup & first print

Daily & weekly maintenance

Troubleshooting

Error messages

Software & drivers

Techniques & settings

Warranty & service plans

Manuals & downloads

Watch DTF Station's video: Prestige L2 and XL2 initial overview

More videos

Prestige L2 and XL2 assembly
Loading and unloading media on the Prestige L2, XL2, XL3 and XL4
Prestige L2 and XL2 daily maintenance
Full maintenance guide for the Prestige XL2 Pro

Embedded from the manufacturer's official channel.

About the Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

The Prestige L and XL printers are DTF Station's roll-to-roll DTF printers. They print onto film from a roll, feed it to a powder shaker, and use Epson PrecisionCore print heads driven by DTF Station Pilot, with neoStampa as the RIP. They share the same stand, ink bay, waste system and most of the same daily routine.

Model Print heads Max print width Inks
L2 (discontinued) 2 Epson i3200 17.72 in CMYK + white
XL2 2 Epson i3200 23.62 in (60 cm) CMYK + white
XL2 Pro Epson i3200HD + i1600 23.62 in (60 cm) CMYK + white + Lc, Lm, G, O (9 colors)
XL3 3 Epson i3200 23.62 in (60 cm) CMYK + white + Lc, Lm, G, O (9 colors)
XL4 4 Epson i3200 23.62 in (60 cm) CMYK + white

What matters for upkeep: the L2 and XL2 need cleaning solution poured into the caps by hand each night. The XL2 Pro, XL3 and XL4 wet the white caps automatically after about 2 hours idle, as long as the cleaning solution bottle stays at least half full, and they add a laser head strike sensor that stops the carriage if something is in its path.

Maintenance schedule at a glance

How often What to do
Every morning Circulate white ink, short ink fill, two head cleanings, nozzle check
Every evening Clean around the heads, the wiper blade and the caps, wet the caps, wipe the bed
Every week Clean the encoder strip, rollers, vacuum holes and sensors, empty the waste bottle
Every month Test the waste ink alarm, grease the carriage rail only if it squeaks
Every 6 months White channel maintenance
About once a year Expect to replace dampers and ink inlet filters. Print heads, caps and wiper blades typically last 1 to 2 years

Where to put it

DTF Station recommends a room at 70 to 75°F with 35 to 45% humidity. Keep fans, air conditioning and heaters from blowing on the printer, since moving air dries the heads, and white dries first. Keep it out of direct sunlight. All five models run on standard 110V power; use a surge protector with battery backup. The machines weigh 300 to 445 lbs, so plan the spot before the crate arrives.