Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Arc 127 cut problems: cutting through the backing, pieces not releasing, cuts off the design, or marks not found
Most bad cuts come down to blade pressure. Run Test Blade on a scrap of the same film and use the lowest Force 1 that cuts cleanly: lower it if the cut goes through the backing, raise it if the piece won't lift out. If the cut line sits too close to the print, raise the weed border offset; if it crosses printed areas on short jobs, shorten the segment length. Marks not found usually means the Start Here arrow wasn't lined up or the job wasn't printed through the Arc 127 queue.
The Arc 127 should cut through the printed film layer and leave the backing whole, so each design lifts out cleanly. When it doesn't, the fix is almost always a setting, not a part. Work through the steps that match what you see, and run a test after each change.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Cuts right through the backing | Force 1 too high, or too much blade showing | Steps 1 and 2 |
| Pieces won't lift out | Force 1 too low, or a dirty or dull blade | Steps 1 and 3 |
| Cut line clips the edge of the design | Weed border offset too small | Step 4 |
| Cut crosses printed areas on a short job | Segment longer than the job | Step 5 |
| Marks not found, or every cut is shifted | Start point, marks or work mode | Step 6 |
| Film moves during the cut | Clamp, vacuum or loading | Step 7 |
Step by step
-
Find the right blade pressure
Put a scrap of the same film under blade 1 and press Test Blade on the cutter's screen. Blade 1's pressure is Force 1; Force 2 belongs to a second blade that the standard setup doesn't use. If the test cuts through the backing, lower Force 1. If the test piece doesn't peel out easily, raise it. Change it a few steps at a time, retest, and settle on the lowest value that cuts cleanly. Repeat this whenever you change film or fit a new blade, because DTF and UV DTF film need different pressures.
-
Check blade exposure
Take the holder out and look at it straight from the side. Only the tip should show, about 1 mm. The user manual's rule is to expose only as much blade as the material needs. Extra blade cuts into the belt, damages the holder and wears the blade fast.
-
Clean or replace the blade
With the cutter off and gloves on, loosen the holder screw, remove scraps and adhesive, and wipe the blade and holder with isopropyl alcohol. If cuts are still rough or incomplete after cleaning and a fresh pressure test, replace the blade.
-
Move the cut line away from the print
In DigiRIP open Q Properties > Cutter Options > Weed Border. The offset is the gap between the printed edge (solid line in the preview) and the cut line (dotted line). DTF Station's queue uses 1.5 mm. Raise it to 2 mm if the blade is nicking designs, and adjust for the artwork. Leave the Contour Cut tab at its defaults.
-
Fix cuts across short jobs
In Q Properties > Production Markup, the job is split into segments, 500 mm long by default, each with its own marks. If the whole job is shorter than one segment, the cut can land on printed areas. Drop the segment length (DTF Station uses 350 mm in that case). Then open Cutter Options and set Virtual Tiling Length to the same number as the segment length, with Virtual Tiling ticked. If the two don't match, or tiling is off, roll cutting gives errors. More segments mean slower cutting, since the cutter stops to read the marks for each one.
-
Get the marks found
Print through the Arc 127 queue for your printer, not your normal print queue, so the marks are added. In Production Markup, keep Mode on Per Content, mark color black, offset 4 mm, and Do Not Apply Processing Options to Markup Systems ticked so no white or varnish prints over the marks. On the cutter, line up the Start Here arrow with the first mark, clamp, and move blade 1 over that first mark before you start. The cutter's Work Mode (under ADVANCED SETTING) should be 1 for rolls or 2 for single sheets; mode 0 is blind cutting with the camera off. After power-on, give the camera about 10 seconds to start (its icon appears in the lower left).
-
Hold the film still
Center the film with the scales and refit the tension bar on rolls. Press Clamp to lock it and turn on the vacuum before cutting. Keep the bed free of scraps so the vacuum can grip. For sheets, DTF Station's DigiRIP workflow keeps the page to 600 x 600 mm or smaller.
Don't press Restore factory parameters on the cutter's screen to fix a cut problem. The user manual says to choose No, because the cutter's settings were made at the factory.
Still cutting off the design after these steps? Text us a photo of the cut film next to the screen showing Force 1, and a screenshot of your Production Markup tab, at (562) 609-4996.
Watch DTF Station print and cut a DTF roll with the Arc 127 and Prestige XL3
More videos
Embedded from the manufacturer's official channel.
Common questions
What Force 1 setting should I use?
There is no single number. In DTF Station's videos, DTF film on the XL3 started at 35 and cut cleanly at 25, while UV DTF film from the Aries 124 needed it raised from 30 to 40. Test every new film and every new blade.
What is Force 2?
The pressure for a second blade. DTF Station's standard DTF and UV DTF setup uses blade 1 only.
How far from the design should the cut line be?
DTF Station's queue sets the weed border offset to 1.5 mm, and 2 mm gives a safer margin. At 0 the blade can cut into the print.
Should I use Restore factory parameters on the cutter?
No. The user manual says to choose No, because the cutter was set up at the factory. Text us instead.
The camera light won't come on, or the cutter keeps failing to find marks after a repair. What now?
Stop and text us a video of the screen and the camera area. That points to the camera or its board, not your settings.
- DTF Station: Arc 127 operation guide
- DTF Station: Arc 127 quick start guide (setup, driver, connection, preparing the cutter)
- DTF Station: Arc 127 user manual (PDF)
- DTF Station technical documentation
- AA and DTF Station support requests about the Arc 127, 2024 to 2026











































































