Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Arc 127 maintenance: end-of-day blade cleaning and air release, and weekly water draining
At the end of each day, power the cutter off, shut off and unplug the compressor, close its valve and pull the air tube so the trapped air escapes. Then clean the blade and holder with alcohol, vacuum the cutting bed, empty the catch basket and cover the machine. Once a week, drain the water from the filter bowl inside the cutter and from the compressor's tank.
The Arc 127 needs very little daily care, but the two jobs it does need matter. Scraps and adhesive on the blade spoil cut quality. Water from the compressed air collects in the lines, and the user manual warns that leaving it there makes the air cylinders work harder and can damage the pneumatic parts.
End of day
-
Power off the cutter
Turn off the main power switch and unplug the main power cord.
-
Shut off the compressor
Press the compressor's power switch down to turn it off, close the air outlet valve on the compressor, and unplug it.
-
Release the air
Pull the connector's lock backward and take the air tube out. That lets the air trapped inside the cutter escape so water can't sit in the system overnight.
-
Clean the blade and holder
Put on gloves. Loosen the screw that holds the blade holder and remove it. Pick off any film scraps around the blade and holder, then wipe both with isopropyl alcohol on a lint-free wipe. Refit the holder before you start the next day, checking that only the tip of the blade shows.
-
Clear the bed and basket
Vacuum the cutting platform to pick up small scraps, and empty the waste film from the catch basket.
-
Cover the cutter
Put the dust cover on so dust and debris stay off the belt and camera overnight.
Never reach near the blade or the carriage while the cutter is powered. Always switch off and unplug first.
Once a week
-
Drain the filter bowl in the cutter
Go to the take-up reel side of the machine and remove the cover. The oil and water filter is on the right, with a clear bowl underneath. If you can see water in the bowl, hold a paper towel under it and pull the drain ring down until the water is gone.
-
Drain the compressor tank
Find the drain plug on the compressor's air tank, underneath the machine. Unscrew it and let all the water run out, then screw it back in snugly.
Match your symptom
| What you see | Likely cause | What to do |
|---|---|---|
| Ragged edges, pieces won't pop out | Dirty or worn blade | Clean it, run a blade test, then replace it |
| Water in the filter bowl every week | Normal condensation | Keep draining weekly |
| Clamp slow or weak | Water in the air system, or low air pressure | Drain the bowl and tank, check the gauge passes 60 psi |
| Film slides during cutting | Scraps on the bed, vacuum not on | Vacuum the bed, turn the vacuum on before cutting |
Cut quality problems that cleaning doesn't fix are covered in our Arc 127 cut problems guide. If the clamp stays weak after draining, or you find oil or a lot of water every day, text us a photo or short video at (562) 609-4996.
Watch DTF Station's video: Arc 127 daily maintenance
More videos
Embedded from the manufacturer's official channel.
Common questions
Why do I have to release the air every night?
Compressed air carries moisture. Releasing it at the end of the day keeps water from building up inside the machine, where it can damage the air parts.
The manual says drain the filter monthly, but DTF Station says weekly. Which is right?
Follow DTF Station's weekly routine. The manual's once a month is the bare minimum, and draining more often does no harm.
What should I clean the blade with?
Alcohol. We use isopropyl alcohol on a lint-free wipe. Wear gloves, because the blade is very sharp.
When should I replace the blade?
When cuts come out rough or don't go all the way through, even after you clean the blade and rerun the blade test.
- DTF Station: Arc 127 maintenance guide
- DTF Station: Arc 127 user manual (PDF)
- DTF Station: Arc 127 quick start guide (setup, driver, connection, preparing the cutter)
- DTF Station technical documentation
- AA support requests about the Arc 127, 2024 to 2026











































































