Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Arc 127 cutter with an Aries 124 or Prestige XL3: DigiRIP cutter add-on, queue import and your first cut job
DigiRIP needs the cutter add-on before it can drive the Arc 127. Install the Arc 127 under Devices, then drag DTF Station's Arc 127 queue file for your printer (Aries 124 or Prestige XL3) into DigiRIP, click Yes, and start the queue from the Main tab because new queues install switched off. Print through that queue so registration marks are added, test the blade, align the first mark and send the job with Cut Job.
The Arc 127 cuts printed DTF and UV DTF film along the outlines of your designs, reading registration marks that DigiRIP prints beside them. Everything is driven from a dedicated Arc 127 queue in DigiRIP (CADlink Digital Factory 11), and DTF Station supplies ready-made queues for the Aries 124 and the Prestige XL3. The physical setup (air, blade, power) is covered at installation and training; this guide is the software side and your first cut.
1. Make sure DigiRIP can drive a cutter
-
Check the cutter add-on
In Digital Factory, go to Devices > Manage Devices. If the Install Cutter icon is grayed out, your license doesn't include the cutter add-on yet.
-
Unlock it
Under Help > About Digital Factory > More, note the license file number that starts with the letter P. If you bought the add-on, enter its code under Help > Upgrade License and restart if asked. No code? Contact us to check whether the add-on is on your order.
-
Install the Arc 127
Back in Devices > Manage Devices, click Install Cutter, search for Arc 127, select it and click OK, Next and Finish.
2. Import the Arc 127 queue for your printer
-
Get the queue files
Download the Arc 127 queue package (a ZIP file) from the link DTF Station provides with the cutter, and extract it. Inside are queue files for each supported printer. Can't find it? Text us and we'll send it.
-
Drag it in
Open DigiRIP next to your normal print queue (your regular Aries 124 UV DTF queue or XL3 DTF queue). Drag the Arc 127 queue file for your printer into DigiRIP and click Yes when it asks to install the queue.
-
Start the queue
New queues install switched off. Go to the Main tab and click Start/Stop Queue so the Arc 127 queue is active.
-
Confirm the cutter is attached
Under Q > Manage Queues, the Arc 127 should show as the device for that queue. If it doesn't, pick Arc 127 from the Device list and click Yes.
The imported queue already carries DTF Station's recommended cut settings. You'll find them under Q > Properties if you ever need to check them:
| Setting | Tab | DTF Station's setting |
|---|---|---|
| Mode | Production Markup | Per Content |
| Mark offset | Production Markup | 4 mm for DTF |
| Segment length | Production Markup | 500 mm; 350 mm if the whole job is shorter than 500 mm |
| Virtual tiling | Cutter Options | On, same length as the segment |
| Weed border offset | Cutter Options | 1.5 to 2 mm |
| Start marks and From End of Roll | Cutter Options | On |
| White and varnish on marks | Processing Options | Off (marks print in black only) |
More segments mean longer cutting, because the cutter stops to read the marks for each one.
3. Choose how files get to the cutter
| Method | What you do |
|---|---|
| USB flash drive (DTF Station's main method) | Set the queue's output folder under File > Port Properties. Cut files land there, and you carry them to the cutter on the flash drive |
| USB cable | Install the Arc 127 Windows driver from the cutter's flash drive or download folder, then pick the COM port it creates in the queue's port settings |
| Ethernet | Needs a fixed IP address on the computer and a TCP/IP port (RAW, port 9100) in DigiRIP. Text us and we'll walk you through the addresses |
4. Print and cut a roll
-
Print through the Arc 127 queue
Select the Arc 127 queue for your printer, so the registration marks and settings apply. Choose your print mode, import and lay out the artwork, and print. For sheets, keep the page to 600 x 600 mm (24 x 24 in) or less.
-
Test the blade
Put a scrap of the same film under blade 1 and press Test Blade. Blade pressure is Force 1 (Force 2 isn't used). If the test cuts right through the film, lower Force 1; if the cut piece doesn't lift out easily, raise it. Use the lowest pressure that cuts cleanly. The blade tip should barely show below its holder, about 1 mm.
-
Load and align
Load the film and center it with the scales. Press Clamp to release, use the left arrow to move the film until the Start Here arrow lines up with the first registration mark, then press Clamp again and turn on the vacuum. Move blade 1 over the first registration mark.
-
Send the cut
In DigiRIP, select the printed job and click Cut Job. With the flash drive method, copy the cut file from the output folder to the drive, plug it into the cutter, choose USB Drive, select the file and start. With a cable or Ethernet, the job goes straight to the cutter.
Too much blade showing damages the belt and wears the blade early. Keep exposure to the bare tip.
Registration marks not found, or cuts landing off the print? Text us a photo or short video at (562) 609-4996 of the film on the cutter bed and your queue's Production Markup tab.
Watch DTF Station import the Arc 127 queue for the Aries 124
More videos
Embedded from the manufacturer's official channel.
Common questions
The Install Cutter icon in DigiRIP is grayed out. Why?
Your license doesn't include the cutter add-on yet. Enter the upgrade code under Help > Upgrade License, or contact us to check whether the add-on was purchased.
I imported the Arc 127 queue but nothing happens. What did I miss?
New queues install inactive. Go to the Main tab and click Start/Stop Queue.
What's the best way to send jobs to the Arc 127?
DTF Station uses the USB flash drive as the main method: DigiRIP saves the cut file to an output folder, and you load it on the cutter from the drive. A USB cable or Ethernet also works once set up.
How hard should the blade press?
Use the lowest Force 1 setting that cuts cleanly. Test on scrap film: if it cuts right through, lower it; if the piece won't lift out, raise it.
How big can a sheet be?
DTF Station's sheet workflow keeps the page to 600 x 600 mm (24 x 24 in) or smaller.
- DTF Station: Arc 127, how to import queue properties for the Aries 124 UV DTF printer
- DTF Station: Arc 127 quick start guide (initial setup)
- DTF Station: Arc 127 operation guide
- DTF Station technical documentation
- AA support requests about the Arc 127, 2024 to 2026











































































