Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Arc 127 setup: uncrating, assembly, air compressor, power and the first function test
Plan for a forklift or at least six people, keep the crate for 6 months, and give the cutter 2 ft of room on every side. Fit the screen, media rods and catch basket, connect the compressor and check its gauge passes 60 psi, install the blade with only the tip showing (about 1 mm), plug in to dedicated power, then test the arrows, vacuum and clamp. Software setup and training come next.
The Arc 127 ships in a wooden crate and weighs 485 lbs, so most of the work is getting it out safely and set up in the right spot. This guide gets you to a cutter that powers on and passes its basic tests. Connecting it to DigiRIP is covered in our Arc 127 DigiRIP guide, and DTF Station's technicians handle training.
Before the crate arrives
- Tools: a 17 mm nut driver bit, a metric hex screwdriver set, a wrench or pliers, a drill and a hammer.
- Lifting: a forklift is best. Without one, use lift straps and at least six people.
- Space: a permanent spot on a level floor with at least 2 ft clear on all four sides.
- Power: dedicated circuits (see step 7). Book an electrician now if you aren't sure.
- The crate: keep it for at least 6 months. DTF Station requires it for warranty purposes.
Unpack and assemble
-
Open the crate
Remove the hex screws along the top and lift off the lid. Hold each nut with a wrench or pliers while you drill out the side panel screws, then tap the panels loose with a hammer and take them off one at a time, along with the top frame. Keep all hardware in a box. Peel the plastic cover off slowly, watching the screen attachment on the left side.
-
Lift the cutter out
Take out the accessory boxes and the wooden slabs first. Lift the cutter off the base with a forklift, or with straps and six or more people, then retract the foot stoppers so it can roll.
-
Check the accessories and fit the screen
Unpack everything and check it against what you ordered. Contact us right away if anything is missing. Unwrap the screen, attach it to the cutter body and look over its cable connections. Gently push home any connector that is only partly seated. If you're unsure, leave it and text us a photo.
-
Install the media rods and catch basket
Slide the rounded rod into its slot. Attach the media brackets with their three screws each, left loose for now. Loosen the rod screws, slide the media holding rods in, center both, and snug the rod screws without overtightening. Then tighten the bracket screws. Loosen the catch basket screws part way, slide its brackets in and hang the basket.
-
Look over the wiring
Wiring can loosen in transit. With the cutter unplugged, turn it around and open the bottom cover to check the breaker connections for loose wires. DTF Station's setup snugs these terminals; if you're not comfortable working on electrical parts, have an electrician do it or text us before powering on.
Air, blade and power
-
Connect the compressor
Assemble the silencer onto the compressor. Wrap plumber's tape on the valve threads and fit the female coupler, then connect the air pipe's male coupler to it. Plug the compressor in, release its power button, open the air valve and check that the gauge climbs past 60 psi. Inside the cutter's back cover is a second regulator that DTF Station sets to about 20 psi. If yours reads far from that, text us before you adjust it.
-
Install the blade
Wear gloves: the blade is very sharp. Take the blade and holder from the accessory box, slide the blade out of its sleeve and into the holder. Look at it straight from the side: only the very tip should show, about 1 mm. Fit the holder into the carriage and lock it.
-
Plug in to the right power
Check each plug's wires are fully seated. A 220V cutter uses one plug for the machine and vacuum, on an outlet good for at least 20 amps. A 110V cutter has two plugs that must go on separate breakers, with the vacuum plug on a breaker rated up to 20 amps. Release the red emergency stop by turning it, then press the power button. The cutter returns to its starting position (the carriage moves to the front corner) and the main screen appears. The user manual says to give the camera about 10 seconds to start; its icon shows in the lower left of the screen.
Too much blade showing cuts into the belt and ruins blades quickly. If you can see more than the tip, push the blade back into the holder before you start.
First function test
-
Arrows
Press left, right, up and down on the screen and watch the carriage follow each one.
-
Vacuum
Lay a sheet of film or paper on the belt and turn on the vacuum. Try to slide it: it should be held firmly.
-
Clamp
Press the clamp button and check the clamp comes down onto the belt. Press it again to release.
Every working day after setup
Close the compressor gauge's outlet valve, pull the hose lock back, push the air tube straight in and push the lock forward until it clicks. Tug the tube to be sure. Plug in the compressor (into the cutter on 220V units, its own outlet on 110V units), open the valve, pull the power switch and watch the gauge rise. Then power on the cutter and wait for it to finish starting up.
Something not moving, no vacuum, or the clamp not closing? Text us a short video at (562) 609-4996 before you go further.
Watch DTF Station's video: Arc 127 uncrating and setup
More videos
Embedded from the manufacturer's official channel.
Common questions
Do I have to keep the crate?
Yes. DTF Station asks you to keep the original crate for at least 6 months for warranty purposes.
My cutter is 110V. Can both plugs go into one outlet?
No. On 110V units the two plugs must go on separate breakers, and the vacuum plug needs a breaker rated up to 20 amps. Have an electrician confirm your circuits.
Where does the compressor plug in?
On a 220V cutter, DTF Station's guide plugs the compressor into the machine. On a 110V cutter, plug the compressor into its own separate outlet.
How much blade should stick out?
Just the tip, about 1 mm, when you look at the holder straight from the side. More than that cuts into the belt and wears the blade out early.
A cable on the screen looks loose. Should I push it in?
DTF Station's guide says to push in any connector that is only partly seated. If you're not sure what you're looking at, leave it and text us a photo.
- DTF Station: Arc 127 quick start guide (setup, driver, connection, preparing the cutter)
- DTF Station: Arc 127 user manual (PDF)
- DTF Station technical documentation
- AA support requests about the Arc 127, 2024 to 2026










































































