Support
Machine type
Brand
DTF Station Prestige R1

Does my Prestige need a new print head? How to tell, how it's confirmed, and what to send us

✓ Reviewed by Jason KimUpdated 3 min readFits: Prestige R1 · R2 · R2 Pro · L2 · XL2 · XL2 Pro · XL3 · XL4 · X6
Short answer

Most poor nozzle checks come from the capping station, wiper, dampers, ink lines or a dried head, not a failed head, so work through your model's cleaning guide first. DTF Station confirms a bad head with a technician-guided swap test: if the fault moves with the head, the head or its cables are at fault. Before ordering, send us your model, serial number, nozzle check photos and what you've tried, and confirm the exact head with us.

A new print head is one of the most expensive parts on a Prestige, and it's often bought when the head isn't the problem. A poor nozzle check is far more often caused by the capping station, wiper blade, dampers, ink lines or a dried-out head that cleaning can recover. This page explains how to tell, how DTF Station confirms a bad head, and what to send us. Fitting a head is a technician-guided job, so we don't cover the installation itself here.

What the nozzle check is telling you

Pattern What it usually points to
Scattered gaps across colors, often after idle time Drying or capping. Work through your model's nozzle check guide first
One color weak or missing while others print That color's ink path or damper, not the whole head
A full straight block of one row missing An electrical contact (cable or board) or a severe clog. Contact us
Every color degraded at once Capping, the room environment or electronics. Contact us

Start with the cleaning and parts checks for your model: R2 Pro and R2, R1 or XL series, plus the capping station, wiper and damper guides they link to.

How DTF Station confirms a bad head

  • Head swap test (R2, R2 Pro, L2, XL2, XL2 Pro, XL3, XL4): the white and color heads trade places. If the missing nozzles move with the head, the head or its cables are at fault. If the problem stays in the same position, the cause is the capping station, dampers, ink system or electronics.
  • Damper swap test (R1): with a single head, dampers are moved between positions to see whether the fault follows the damper or stays with the head channel.

DTF Station does these tests only when a technician suspects a hardware problem, and replaces parts only once the root cause is confirmed. They involve ribbon cables and ink lines, so do them with us on the phone or video, not on your own.

Which heads your printer uses

Printer Print heads
Prestige R1 1 x Epson F1080
Prestige R2 Pro 2 x Epson i1600
Prestige XL2 2 x Epson i3200
Prestige XL2 Pro Epson i3200HD + i1600
Prestige XL3 3 x Epson i3200
Prestige XL4 4 x Epson i3200
Prestige X6 6 x Epson i3200

DTF, eco-solvent and UV versions of the same Epson head look alike but are not interchangeable. Always confirm the exact head with us using your serial number before ordering.

What to send us

  1. Machine details

    Your model, a photo of the serial number label and your order number.

  2. Nozzle checks

    A photo of the nozzle check before cleaning and after the cleanings you've run, laid flat in good light.

  3. What you've tried

    Which cleanings, capping station and wiper checks, damper checks or ink line pulls you've done, and when the problem started.

  4. Supplies and errors

    The ink, film and cleaning solution you use, and any error code or message in Pilot or on the printer.

Our what to send support page has tips for shooting a useful photo and video.

Warranty in short

Print heads are consumable parts, covered only by the conditional print head warranty you earn with training and registration: 6 months from the ship date, for a set number of heads by model. Under DTF Station's print head policy, a head bought after that period has a 14-day window tied to when you receive it, a head is evaluated for defects before any replacement, and damage from mishandling, improper installation or cleaning isn't covered. Returns need the head in its original condition. DTF Station recommends a trained technician for installation.

Think your head is done? Text us a photo or short video at (562) 609-4996 of your nozzle check before you order one.

Watch the print head swap test DTF Station uses to confirm a bad head

More videos

Prestige R1: print head test by swapping the damper positions

Embedded from the manufacturer's official channel.

Common questions

How do I know if my print head is bad?

A head fault is confirmed by a swap test: if missing nozzles follow the head to its new position, the head or its cables are at fault. Scattered gaps after idle time are usually drying or capping, not a dead head.

Can I replace the print head myself?

DTF Station's policy makes the owner responsible for installation and recommends a trained technician. Contact us first and we'll guide you or arrange help.

Is a print head covered by warranty?

Only under the conditional print head warranty earned through training and registration, 6 months from the ship date. Heads bought later have a 14-day window under DTF Station's print head policy.

Which print head does my printer take?

R1 uses one Epson F1080, R2 Pro two i1600, XL2 two i3200, XL2 Pro an i3200HD plus an i1600, XL3 three i3200, XL4 four i3200 and X6 six i3200. Confirm with your serial number before ordering.

I installed a new head and it prints nothing. What now?

Stop and text us a photo of the nozzle check and the head area. After a head change, DTF Station's procedure fills ink through the new head and runs a few cleanings before the nozzle check, and every ribbon cable has to be seated exactly right.

Did this fix it?