Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige R2 Pro and R2 bad nozzle check: how to clear clogs and missing nozzles
Print a nozzle check first, then work up the ladder: run Fill Ink on the affected head, clean the wiper blade, run two head cleanings and check again. If channels are still missing, warm-wet-cap the head with cleaning solution for 15 minutes and clean again. If that doesn't bring the nozzles back, the cause is usually a damper, the wiper or the capping station seal rather than the head, so send us a photo before you buy a head.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| A few gaps in one or two colors | Partial clog or air | Steps 1 to 4 |
| Half a head or more missing | Air in the lines or a heavy clog | Steps 2 to 5 |
| Same channel still missing after a wet cap | Damper, wiper or capping station | Step 6 |
| Good check in the morning, nozzles fade during printing | Head strike residue, airflow, capping height | See the questions below |
| Nothing prints at all, or odd patterns | Electrical or software, not a clog | Our error codes guide |
Keep the front cover open while you work. If your printer has a front-cover sensor and stops with a cover error, DTF Station's procedure is to tape the L-shaped head lock bracket (the one you removed at setup) in front of the sensor. Take it off when you're done.
Step by step
-
Print a nozzle check
Press Menu, go to Head Maintenance > Head Status and press Enter. In Hosonsoft the same test is the Check button. The left head is color (CMYK) and the right head is white. Photograph the result: you'll compare against it after every step.
-
Run Fill Ink on the affected head
Press Menu > Head Maintenance > Fill Ink and choose Left Head for color, Right Head for white, or Two Head for both. Start timing when ink visibly flows into the waste bottle, let it run 30 seconds, then press Cancel. This pushes air out of the lines.
-
Clean the wiper blade
Press the Left arrow to move the carriage off the capping station. Clean the wiper blade with a foam swab soaked in cleaning solution (a swab, not a lint-free cloth). Press Enter to dock the carriage again.
-
Run two head cleanings, then check again
Press the Cleaning button twice, back to back. Advance the film and print another nozzle check. If it isn't complete, go to step 5.
-
Warm wet cap
Warm some cleaning solution for about 15 seconds in a microwave so it's warm, not hot. Press the Left arrow to move the carriage away. With a syringe, fill the cap under the affected head without overflowing it. Press Enter so the head sits down on the wet cap, and leave it for 15 minutes. Then run 2 to 3 head cleanings and print a nozzle check. If it improved but isn't perfect, repeat the wet cap once.
Never boil the solution or use it hot. Boiling solution can delaminate the head. Don't wipe or scrub the head face. There is a stronger pull-through procedure at the cap pump, but done wrong it twists the pump tube or floods the printer, so we only do it with you on a call.
-
Check the mechanical parts
If the same channels stay missing, open the capping station compartment and watch a head cleaning at eye level:
- The wiper blade should touch the head evenly across its width. If it's bent or slanted, it needs straightening or replacing.
- When you press Enter, the cap should rise and seal against the head, centered under it.
- A single color that never comes back usually points to a bad damper. See our damper guide.
Capping station and wiper heights are set in the control software's protected settings. Don't change them on your own.
-
Send us the evidence
Text us a photo or short video at (562) 609-4996: the latest nozzle check photo, a 1-minute video of a head cleaning filmed from an angle, and a 30-second video of you pressing Enter a few times so we can see how the head meets the cap. With those three we can usually tell you exactly which part is at fault.
Watch DTF Station's video: unclogging and fixing a poor nozzle check on the Prestige R2
Embedded from the manufacturer's official channel.
Common questions
How good does the nozzle check need to be?
DTF Station's rule is to print when at least 90% of the nozzles are firing. Below that you'll see banding, so clean first.
Should I run a cleaning before the nozzle check?
No. Always check first. Cleaning before you know what's wrong wastes ink and can pull air into the head.
My nozzle check is perfect in the morning but colors drop out after a few prints. Why?
The usual causes are dried residue from an old head strike that the wiper keeps spreading, a fan or air vent blowing on the printer, or a capping station that sits too far from the head. Send us a nozzle check from before the job and one from right after it stops.
Can I use window cleaner or a household cleaner on the caps and wiper?
No. Use DTF Station-approved cleaning solution only. Household cleaners and homemade mixes stain the head, leave debris in the caps and damage the wiper rubber.
Is my print head dead?
Usually not, especially in the first 6 months with no head strike. Rule out dampers, the wiper and the capping station seal first. Heads are wear parts and typically last 1 to 2 years.
Should Auto Clean run during printing?
Keep the during-print Auto Clean set to Close (off) and Pre-Flashing set to Open. That's DTF Station's setting for the R2 Pro, and especially important on the original R2's XP600 heads.
- DTF Station: Prestige R2, how to unclog or fix a poor nozzle check
- DTF Station Prestige R2 Pro user manual: maintenance schedule
- DTF Station Prestige R2 Pro Operation Guide
- DTF Station technical documentation
- AA and DTF Station support requests about Prestige R2 and R2 Pro nozzle checks and clogs, 2024 to 2026











































































