Support
Machine type
Brand
DTF Station Prestige R2 (original)

DigiRIP on the original Prestige R2: add the R2 driver, connect to Hosonsoft, and set the white ink

✓ Reviewed by Jason KimUpdated 2 min readFits: Prestige R2 (original) with DigiRIP and Hosonsoft (PrintExp)
Short answer

In DigiRIP, go to Devices > Manage Devices > Install Printer, pick Prestige R2, and when asked for the port choose TCP/IP with address 127.0.0.1. Keep Hosonsoft open and connected to the printer, because DigiRIP hands each job to it. For white, open Queue Properties > Color Layer > Processing Options: Maximum White Ink Percentage starts at 60% and should be changed in 10% steps, and raise the choke if white peeks out past the edges.

The original Prestige R2 is driven by two programs. DigiRIP (DTF Station's edition of CADlink Digital Factory) builds the color and white layers. Hosonsoft, also called PrintExp, is the control software that talks to the printer over Ethernet. DigiRIP passes each job to Hosonsoft on the same computer.

Add the Prestige R2 driver

  1. Open device management

    In DigiRIP, click Devices > Manage Devices > Install Printer.

  2. Pick the R2

    Find Prestige R2 in the list, select it, click OK, and let DigiRIP download the printer package.

  3. Set the port

    When asked for the port, choose TCP/IP and enter 127.0.0.1. Click OK, Next, then Finish.

  4. Check it

    Confirm the R2 appears in your device list with the Production R, Production Res Z and White Graphic print modes. In Q > Manage Queues, the queue port should read TCP/IP, 127.0.0.1, port 9100.

Get jobs through to the printer

  1. Hosonsoft open and connected

    Open Hosonsoft and confirm it's connected to the printer before you send from DigiRIP. If several network adapters are listed under Advanced > Advanced > Net Setting, unplug the printer cable for a moment, see which entry disappears, plug it back and select that one.

  2. NW Receive running

    NW Receive is the small program that passes jobs from DigiRIP to Hosonsoft. Open Task Manager and search for it. If it isn't there, start NWR receive.exe from your Hosonsoft folder on the C: drive.

  3. Clear and resend

    Close Hosonsoft (answer Yes) and reopen it to clear its cache. In DigiRIP, click the clear errors icon and resend. In Hosonsoft's Print tab, the status should change to Printing and the percentage should climb.

  4. Allow it through security software

    Windows Firewall or antivirus can block port 9100. Allow DigiRIP and Hosonsoft, or add an inbound rule for TCP port 9100.

Set the white ink

Only change white once the nozzle check is good. Change one thing at a time and print a test.

Setting Where Default and how to change it
Maximum White Ink Percentage Queue Properties > Color Layer > Processing Options 60%. Change in 10% steps only
White Under Black Same tab 50%. Controls white beneath black areas
Choke Same tab, or Devices > Manage Print Modes to make it stick Higher pulls white in from the edges; lower widens it but can peek out
Highlight white (v11 and later) Under Base and Highlight 100%. If colors bleed or white looks too strong, start at 50% and adjust in 10% steps

Settings in Queue Properties apply to every new image in that queue. To change one image only, double-click it and open the same tab.

If color shows past the white on one side only, the head adjustment values need changing, not the choke. A wrong value makes it worse, so text us and we'll do it with you.

Still stuck? Text us a photo or short video at (562) 609-4996 with screenshots of DigiRIP and Hosonsoft.

Watch DTF Station's video: how to add the Prestige R2 driver

Embedded from the manufacturer's official channel.

Common questions

What print modes should I see after installing the driver?

Production R, Production Res Z, and White Graphic for white-only printing.

How much choke should I use?

Start around 2 to 3 pixels for colored garments and up to 5 for black. If you seem to need more than 5, the white and color heads are probably out of alignment, and we should look at it with you.

I changed the choke and it reset when I switched print modes. Why?

Choke is stored with the print mode. Set it in Devices > Manage Print Modes on the mode you use, save, and reselect that mode in your queue.

Should I move my R2 to NeoStampa?

It's possible with DTF Station's DigiRIP to NeoStampa upgrade. Text us first so we can confirm your printer and software are a fit.

Did this fix it?