Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige XL series poor nozzle check: how to clear clogs and missing nozzles
Most gaps in a Prestige nozzle check come from air in the ink path, a dirty or misaligned cap, or ink drying on the head, not a dead head. Check that the ink valves are open, white circulation isn't too high and the wet cap bottle is full, then run a 30-second ink fill and two cleanings. If that fails, do a warm wet cap. Only then try a manual ink pull. If the whole check is blank, or there is a red light in the carriage, stop and contact us.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| A few gaps scattered across the check | Partial clog or air | Steps 1 to 3 |
| One color always missing | That color's damper, filter or tube | Step 4 |
| Gaps that won't clear after cleanings | Dried ink on the head or a heavy clog | Steps 5 and 6 |
| Good check in the morning, channels drop after a few prints | Airflow on the heads, an old head strike, cap height | Step 1, then contact us |
| Nothing prints at all, or a red light inside the carriage | Electrical: cable or board | Stop and see our warning lights guide |
| Only white is missing | White ink path | Our white ink guide |
Print a nozzle check after every step. Once it's good, stop.
Step by step
-
Check the basics
At the back, make sure every ink valve is open (the handle points toward you). Turn white circulation down if it's set high. Check that the cleaning solution bottle is full and that its tube to the white cap has no air bubbles. On the XL2 Pro, XL3 and XL4, move the carriage left and press the wet cap button until the white cap fills with solid solution. Leave ink bottle caps loose.
-
Ink fill, then two cleanings
Go to Menu > Head Maintenance > Fill Ink, select all heads and run it for 30 seconds. Solid ink with no bubbles should come out of the waste tubes. Then run two head cleanings back to back. With the cover open during a cleaning, watch that the carriage, capping station and wiper move properly and that no ink spills outside the caps.
-
Target one head
If only one head is bad, run an ink charge on just that head in Pilot for 10 seconds or more, then a normal cleaning on that head. On the XL2 Pro, H1 is color and H2 is white.
-
Look for air at the dampers
Move the carriage to the center, remove the film and power off. Take off the carriage cover and look at the dampers and the ink lines above them for bubbles, and check that each line is pushed fully onto its damper. Open the side panel and make sure no ink tube is twisted or kinked. A damper you suspect can be tested with a syringe: hold it only by its hard plastic frame and pull slowly from the bottom. Solid ink is fine. Air or bubbles that keep coming mean the damper needs replacing.
-
Warm wet cap
Warm some DTF cleaning solution until it is warm, never boiling. Move the carriage left and fill each cap with it using a syringe, without making bubbles. Dock the carriage and leave it for 5 minutes. Then run a 30-second ink fill and two cleanings. If you see improvement, repeat it and leave the heads soaking overnight.
-
Manual ink pull (heavy clogs)
Only after steps 1 to 5. With the carriage docked and powered off, open the right side panel. On the L2 and XL2 the top line is white and the bottom is color; the XL2 Pro has an H1 (color) and H2 (white) pump tube. Disconnect the line by turning it counterclockwise, attach a large syringe firmly, pull and hold. Repeat until you've drawn about 60 mL in total. Reconnect so the tube rests straight with no twist, power on, run two cleanings and print a check.
If you feel no resistance when you pull, there is an air leak. Stop and contact us. A badly done ink pull, especially one that leaves the pump tube twisted, can make things worse than before.
When to contact us
- The nozzle check is completely blank, or a red light is on inside the carriage.
- The pattern doesn't change at all after steps 1 to 6.
- You suspect the caps are out of line with the heads. Cap height and alignment settings are in a password-protected menu, and we'll walk you through them.
Text us a photo of your nozzle check and a short video of a head cleaning at (562) 609-4996.
Watch DTF Station's video: troubleshooting a poor nozzle check on large-format Prestige printers
Embedded from the manufacturer's official channel.
Common questions
How many cleanings should I run before calling?
Don't run dozens. If two rounds of a 30-second ink fill followed by two cleanings don't change the pattern, move on to the next step or contact us. Repeated cleanings just waste ink.
My nozzle check is perfect in the morning but channels drop out after a few prints. Why?
Common causes are a fan or air conditioner blowing on the printer, film that buckled and brushed the heads (even weeks ago), and a cap that sits too far from the heads. Print a nozzle check before and after the job and send us both photos.
Only one color is missing. What does that mean?
Usually that color's ink path: its damper, filter, tube or valve, not the whole head. The damper check in step 4 tells you a lot.
My printer is over a year old. Could it be the head?
Possibly. DTF Station rates print heads at about 1 to 2 years, and dampers and inlet filters at about a year. Work through the steps first; we'll help you decide whether a part is due.
Can I use a household cleaner or a homemade mix on the heads?
No. Use DTF cleaning solution only. Household cleaners can stain the head plate, leave debris in the caps and damage the wiper blade.
- DTF Station technical documentation
- DTF Station video: How to Troubleshoot Poor Nozzle Check on Your Large Format Prestige Printers
- DTF Station video: Fixing Heavy Clogs, Prestige L2 and XL2
- DTF Station video: Prestige XL3, How to Perform Fill Ink, Head Cleaning, Nozzle Check
- AA support requests about Prestige XL series nozzle checks and clogs, 2024 to 2026











































































