Support
Machine type
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

Prestige XL series blurry, doubled or misaligned prints: calibration, encoder strip and carriage belt

✓ Reviewed by Jason KimUpdated 2 min readFits: L2 · XL2 · XL2 Pro · XL3 · XL4 (head calibration steps: XL2 Pro · XL3 · XL4)
Short answer

Blurry or doubled edges usually mean the bidirectional calibration is off or the encoder strip is dirty. White and color that don't line up often mean the take-up motor was left off after a film change; if not, redo head and channel calibration. Fine horizontal banding is usually step calibration. A carriage that knocks, stops mid-print or drifts out of alignment points to the drive belt.

Match your symptom

What you see Most likely cause Go to
White and color layers don't line up, especially after changing film Take-up motor left off Step 1
Blurry or doubled edges Dirty encoder strip, or bidirectional calibration Steps 2 and 6
Fine horizontal lines or banding Step calibration Step 3
White offset from color on every print Head calibration Step 4
One color slightly offset Channel calibration Step 5
Knocking as the carriage moves, carriage stops mid-print, layers drift Carriage drive belt Belt section below

Step by step

  1. Check the take-up motor and film

    After a film change, make sure the take-up motor switch is back on (position 1) and the tension bar is raised. A slack or dragging roll shifts the film between passes and pulls white and color apart.

  2. Clean the encoder strip

    The encoder strip is the clear strip running behind the carriage. Wipe it left to right with 90% or stronger isopropyl on a lint-free cloth. Do this weekly anyway.

  3. Step calibration

    In Pilot, go to Calibration > Step Calibration > Test Print. Find the value where the two black lines merge into one solid line (usually -1, 0 or +1), enter it, apply and print again. When the best line sits at 0, save.

  4. Head calibration (XL2 Pro, XL3, XL4)

    On the Head Calibration tab, print the left, right and vertical tests. Each shows black blocks with white over them; find the number where white fully covers black. For the left test, add that number to the current H2 value. For the right and vertical tests, subtract it. Save and reprint each until the best match is at 0.

  5. Channel calibration

    Go to Calibration > Channel Calibration > Left Direction, with white paper under the bed so you can read it. Black (channel 4) is the reference and stays at 0. For each other channel, find the bar that lines up best and enter that offset. Save, reprint, then repeat for Right Direction.

  6. Bidirectional calibration (always last)

    Go to Calibration > Bidirectional Calibration > Test Print. Find the bar where the dark and light patterns overlap perfectly (zoom in with a phone camera). Add that number to the current value, enter it, save, advance the film and print again. The best bar should now be 0.

Carriage drive belt

On the L2, XL2, XL3 and XL4, a worn or loose drive belt shows up as knocking while the carriage moves, the carriage stopping mid-print, or white and color layers that won't stay aligned even after calibration. Replacing it means removing the carriage cover and gear brackets, then setting the motor position and belt tension so the belt moves about half an inch when pulled gently. Send us a short video of the carriage moving first so we can confirm the belt is the cause.

Replacing the encoder strip

A scratched or stretched strip is replaced from both ends with the carriage centered and the printer off. The new strip must run through the encoder sensor and sit centered in every guide. Afterward, Pilot needs a gear ratio check in a password-protected menu, followed by a new bidirectional calibration. Contact us before you start so we can take you through the protected step.

Watch DTF Station's video: bidirectional calibration on Prestige printers

Embedded from the manufacturer's official channel.

Common questions

In what order should I calibrate?

Step calibration first, then head calibration (multi-head printers), then channel calibration, and bidirectional last. Bidirectional depends on all the others.

My step calibration gives different answers every time. Why?

Check the vacuum, the condition of the film, the pinch rollers and the film tension. Calibration can't be accurate if the film moves unevenly.

How do I clean the encoder strip?

Weekly, with 90% or stronger isopropyl on a lint-free cloth, wiping left to right. Ink mist on the strip is a classic cause of blurry prints.

I replaced the encoder strip and now get a pulse error. What's wrong?

The strip probably isn't running through the encoder sensor. Check it with a flashlight from the other side and make sure it's centered in every guide. A replaced strip also needs a gear ratio check in Pilot's protected settings; we'll walk you through that.

Can I replace the carriage belt myself?

It's doable with the video, but it involves setting gear position and belt tension. Contact us first so we can confirm the belt is the problem.

Did this fix it?