Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige XL series setup: assembly, computer connection and first nozzle check
Assemble the stand and accessories, remove the carriage lock, and connect a Windows PC by Ethernet, then stop. In the US, wait for your on-site training before filling ink, and never fill ink on an XL3 or XL4 during self-assembly. Keep the crate for at least 60 days. Your first nozzle check should be nearly complete (about 90 to 95%) before you print production work.
Before the crate arrives
- Computer: Windows 11, Intel i5 or i7 at 2.6 GHz or faster, 8 GB of RAM or more, 500 GB free (an SSD is better), and Ethernet.
- Space and power: a level floor, a standard 110V outlet, and a surge protector with battery backup.
- Helpers: two people minimum for an L2 or XL2, four to five for an XL3 or XL4.
- Supplies on hand: ink, film and powder, so training isn't held up.
Keep the crate for at least 60 days. DTF Station requires it for warranty purposes. If anything is missing when you check the parts against the packing list, contact us right away.
Assembly
-
Build the stand
Fit the legs into the feet and start every bolt before you tighten any. Mount the front crossbar with its L and R labels facing forward. When the tension rod is in, it must slide up and down freely. On the XL3, lower the wheel stoppers to the floor by turning them counterclockwise once the stand is in place.
-
Lift the printer on
Line the pins up with the holes, remove the crate mounting plates and bolt the printer to each leg.
-
Fit the accessories
Install the cleaning solution bottle holder, the waste bottle holder, the feed reel and the take-up reel. Mount the media sensor facing the back of the printer and route its cable under the crossbar, never over the tension bar.
-
Set up the waste and cleaning solution lines
Cut the waste tube at an angle so it reaches into the bottle without touching the waste ink. Test the waste alarm by turning the empty bottle upside down. The cleaning solution tube must reach the bottom of its bottle. On the XL3 and XL4, thread the wet cap tubes through the front hole.
-
Release the carriage
Open the front lid, remove the carriage lock bracket with an Allen key, and store it with the crate hardware. You need it again if the printer is ever moved. Remove all transport tape inside and out.
-
Power on
Switch on at the rear, then release the emergency stop button(s) by turning them clockwise. Wait for Idle on the control panel and check that the carriage parks on the capping station.
Stop here. US customers should wait for on-site training before filling ink or setting up software. On the XL3 and XL4, DTF Station's instructions are explicit: do not fill ink during self-assembly.
Connecting the computer
The printer talks to Pilot over Ethernet. Your computer's Ethernet adapter needs a fixed address in the same range as the printer (for example 192.168.127.16). Never use an address ending in 10. If the connection shows red in Pilot, try a different cable or adapter, or a different last number. Your technician will set this with you.
On L2 and XL2 printers built before December 2024, a "failed to load parameters" message means the printer needs a board and firmware upgrade before it will connect. Contact us. Don't update Pilot or firmware on an L2 or XL2 on your own: on some units it can leave the printer unable to start.
Load film and run the first nozzle check
-
Load the roll
Handle the roll by its core, printable side out. Route the film under the tension rod, lift the pinch rollers, feed the film across the bed, and lower the rollers. Set the media guides close to the film edges but not tight against it.
-
Set the print start position
Measure from the edge of the last pinch roller to where you want printing to begin, convert it to millimeters, and enter it in Pilot under Print Start Position. With the film centered, this is usually around 50 to 70 mm.
-
Print a nozzle check
Close the cover and press Nozzle Check on the control panel with Pilot open. A good pattern is close to complete, about 90 to 95%. If it isn't, see our guide to poor nozzle checks on the Prestige XL series.
Watch DTF Station's video: assembling the Prestige L2 and XL2
Embedded from the manufacturer's official channel.
Common questions
Can I run the printer from a Mac or a Surface tablet?
No. Pilot needs a Windows PC with an Ethernet port (a USB Ethernet adapter is fine). Macs and tablets, including the Surface Pro, are not supported.
Do I really need to keep the crate?
Yes. DTF Station asks you to keep it for at least 60 days for warranty purposes. Keep the carriage lock bracket too.
Pilot says it failed to load parameters. What now?
On L2 and XL2 printers built before December 2024, this means the printer needs a motherboard and firmware upgrade before it can connect. Contact us. Don't try to update the firmware yourself.
How many people do I need?
At least two to lift an L2 or XL2 onto its stand, and four to five for an XL3 or XL4.
Can I fill the ink myself to save time?
Wait for your technician. Ink filling includes priming the dampers, which your technician does with you.
- DTF Station technical documentation
- DTF Station video: Prestige L2 and XL2, Assembly
- DTF Station video: Prestige XL3, Assembly
- DTF Station video: Prestige XL2 Pro, Assembly
- DTF Station video: Prestige XL3, Pilot Software Setup
- AA support requests about Prestige setup, missing parts and computer connection, 2024 to 2026











































































