Support
Machine type
Brand
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36

Miro shaker smoking or dripping oil on prints: purifier, glycerin and filter fixes

✓ Reviewed by Jason KimUpdated 2 min readFits: Miro 13 · Miro 13 Max · Miro 24 · Miro 36 · Miro 36 Pro
Short answer

Smoke from a Miro almost always means the purifier isn't doing its job: either the fan has stopped or the filter is soaked with glycerin, the oily byproduct that cooks out of DTF ink. Check that the purifier fan spins, replace a wet or yellowed filter, and run the purifier at least 5 minutes with the chamber open at the end of every day so glycerin doesn't build up and drip onto prints.

Match your symptom

What you see Most likely cause Go to
Smoke while printing, purifier fan not spinning Fan stopped (glycerin buildup, loose connection or failed fan) Steps 1 to 3
Smoke while printing, fan is spinning Wet, yellowed or clogged filter Step 4
Oily drops on finished prints Glycerin buildup and skipped cool-down Steps 5 and 6
Clear oily liquid in the chamber after it cools Normal glycerin from the ink Step 6

Step by step

  1. Power off and cool down

    Turn the shaker off and let the heating plate cool to room temperature. Have gloves, a lint-free cloth and a screwdriver ready.

  2. Check the purifier fan

    Open the purifier chamber and turn the power on. The fan should spin. Look around the fan motor for glycerin buildup and clean it off with the power off.

  3. If the fan won't spin

    A loose wire connection or a failed fan is next. Checking the wiring means lifting the heating plate on a cooled, unplugged machine, so text us first and we'll walk you through it and confirm whether you need a new fan.

  4. Inspect the filter

    If the fan runs but smoke continues, open the purifier chamber and look at the filter. Yellow staining or a damp feel means it's saturated with glycerin. Replace it with the filter made for your model.

  5. Burn off the glycerin

    Open the heating chamber or purifier chamber and let the purifier run at least 5 minutes to clear the excess.

  6. Clean it out

    Once cool, brush loose powder out of the chamber and wipe it with 90% or stronger isopropyl alcohol on a lint-free cloth. Pay extra attention to the sides where glycerin collects, especially near the wiring connections, and to the area around the purifier fan.

The routine that prevents it

  • Every day: turn off everything except the main power and purifier, open the main chamber, and let the purifier run at least 5 more minutes while it cools. Then wipe the chamber, the top and the outer filter cover.
  • Every week: remove and clean the glycerin catch trays on both sides with isopropyl alcohol.
  • Every month: replace the purifier filter, air vent filter and fabric top cover. Keep spares on hand.
  • Miro 36: take the HEPA and charcoal filters out daily to dry and fit the spare set, charcoal side up. If smoke persists, turn on both purifier fan switches.
  • Miro 36 Pro: swap in a dry filter set daily or every 100 meters, with the cold catalyst filter in layer 1 and the carbon filter in layer 2, label up. Open the drain valve after each day's printing so oil runs into the collection box, and wipe or replace the sponge as needed.

Built-in purifiers don't replace room ventilation. Keep a window open or a fan running while you print.

If smoke continues after a new filter and a clean chamber, text a short video to (562) 609-4996.

Watch DTF Station's video: fixing smoke and fume problems on the Miro 13 and 13 Max

Embedded from the manufacturer's official channel.

Common questions

What is the clear, oily liquid in my shaker after it cools?

Glycerin. It's in DTF ink to keep it from drying and it evaporates out during curing. Some of it is normal, which is why the daily wipe-down and weekly catch tray cleaning exist.

How often do the filters need replacing?

Monthly on the Miro 13, 13 Max, 24 and 36, along with the air vent filter and fabric top cover on the smaller models. On the Miro 36 Pro, swap in a dry spare set every day or every 100 meters and replace a set once it's blackened or smoke comes through quickly.

Can I wash the filters?

No. Let a damp filter air-dry in a shaded, ventilated spot, and replace it if it's saturated.

Which filter fits my Miro 13 Max?

The 13 Max uses its own filters. The filter sold for the Phoenix Air 16x20 and original Miro 13 does not fit the 13 Max.

Can I use rubbing alcohol to clean the chamber?

Use 90% or stronger isopropyl alcohol on a lint-free cloth. DTF Station specifically says not to use rubbing alcohol.

Did this fix it?