Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
DTF powder curing temperature and time: shaker and oven settings
Color Prime powder and Glide Pro film are specified at 125°C (257°F) for 60 seconds, and DTF Station treats 120°C (248°F) as the minimum the powder must reach. Desktop ovens often need more: the Phoenix Air manual and Color Prime's sheet film instructions suggest 140°C (284°F). A good cure looks like glossy orange peel. Grainy means undercured; film that won't peel after pressing can mean overcured.
Starting points by setup
| Setup | Start here | Source |
|---|---|---|
| Any shaker with Color Prime powder or Glide Pro film | 125°C (257°F) | Color Prime film and powder instructions |
| Desktop oven, Glide Pro rolls | 125°C (257°F) for 60 seconds | Glide Pro roll instructions |
| Desktop oven, Glide Pro sheets or Universal Peel film | 140°C (284°F) | Color Prime sheet and Universal film instructions |
| Phoenix Air 16x20 | 140°C (284°F) for 60 seconds | Phoenix Air manual |
| Miro 13 Max and Miro 24 main plate | 130°C factory default | Miro manuals |
| Seismo L16R and L24R | Powder must reach at least 120°C for 45 seconds to 1 minute | Seismo operation guide |
| Flex powder on a Miro 36 | Main heating above 300°F (149°C) | Color Prime Flex powder instructions |
The number on the display is only useful if it matches reality. Check plates and ovens with an infrared thermometer, especially when results change from one day to the next.
Read the result
| What the cured film looks like | What it means | What to change |
|---|---|---|
| Glossy, slightly bumpy orange peel | Fully cured | Nothing |
| Grainy, sandy or matte | Undercured | Raise the temperature in small steps (5°C on a Seismo) or add time |
| Cured fine, but film won't hot or warm peel and solids bubble | Overcured | Bring the cure back toward 120 to 125°C |
| Glossy in some areas, grainy in others | Uneven heat or film off center | Center the film and measure the plate in several spots |
Step by step
-
Powder promptly
Powder printed film within 2 hours. If the film feels damp or static, warm it for about 1 second first. Apply powder evenly and shake off all the excess.
-
Heat the oven or shaker fully
Give a desktop oven at least 10 minutes to come up to temperature. On roll shakers, let the main plate settle at its set point before production.
-
Cure and inspect
Cure at your starting point, then inspect the surface in good light. Undercured powder is the most common reason prints shrink, bubble or wash off later. DTF Station's tests found powder cured at 90°C (195°F) gave a grainy finish and poor adhesion.
-
Don't overshoot
More heat isn't always better. In the same tests, curing at 160°C (320°F) made the film impossible to hot or warm peel and caused bubbling in large solids.
-
Let it cool before pressing
Wait 5 to 10 seconds after curing before you press, so the powder is no longer molten.
Third-party powders and films can melt at different temperatures. Follow their instructions, and test a sample before a large run.
Not sure if it's cured? Text a close-up photo of the powder surface to (562) 609-4996.
Watch DTF Station's video: 10 common DTF transfer problems, including under- and overcuring
Embedded from the manufacturer's official channel.
Common questions
How do I know the powder is fully cured?
Look at the surface. Fully melted powder has a glossy, slightly bumpy orange-peel texture. If it looks grainy, matte or sandy, it needs more heat or time.
Can I cure with a heat press instead of an oven?
Color Prime's original powder instructions describe hovering a heat press over the film at 340°F for 5 minutes, without touching it. An oven or shaker gives more even results, and you should check the finish either way.
Why do my prints bubble or resist peeling when I press them right after curing?
The powder is still molten. Let the film cool 5 to 10 seconds after curing before pressing, especially with large solid areas.
How soon after printing do I need to powder and cure?
Powder within 2 hours of printing.
Does humidity change anything?
Yes. Damp film makes powder cling and can undercure. In a humid room, warm the film about 1 second before powdering, and raise the preheat on a roll shaker.
- Color Prime Quick Glide Pro DTF Film Rolls, product instructions
- Color Prime Quick Glide Pro DTF Film Sheets, product instructions
- Color Prime Universal Peel DTF Film Rolls, product instructions
- Color Prime Hot Melt Powder, product page
- Color Prime Flex Hot Melt Powder, product page
- DTF Station: Color Prime powders
- Phoenix Air 16x20 DTF Curing Oven user manual (PDF)
- DTF Station: DTF General Troubleshooting (video)
- DTF Station: Seismo L16R and L24R operation guide
- DTF Station: Miro 13 Max user manual (PDF)
- DTF Station: Miro 36 Pro user manual (PDF)
- DTF Station technical documentation
- AA and DTF Station support requests about DTF curing, 2024 to 2026











































































