Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige XL series film feeding problems: take-up reel won't stop or won't wind, pinch rollers and loading
The take-up reel is driven by a sensor that watches the film behind the printer. If the reel keeps spinning or never winds, check that its switch is set to 1, clean the sensor lens with isopropyl, and make sure the sensor sits close to the film path. If the arrow keys won't move the film, power the printer off for 5 minutes and try again. If the pinch rollers won't lift, check the blue light on the power supply.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Take-up reel keeps spinning and throws out film | Sensor dirty, mispositioned or failed | Steps 1 and 2 |
| Take-up reel doesn't wind, film drags | Switch off, sensor, or take-up motor | Steps 1 to 3 |
| Arrow keys won't advance or reverse the film | Controller needs a restart, or a connection issue | Step 4 |
| Pinch rollers won't lift or lower | Power supply, roller sensors, button or relay | Step 5 |
| Film wrinkles, buckles or touches the heads | Loading, guides or tension | Loading checklist below |
Step by step
-
Check the switch
The take-up reel's power switch must be at 1 while printing. With the printer running, watch whether the reel winds when film builds up.
-
Test and clean the sensor
Find the media sensor at the back of the printer. Lift the tension rod so nothing blocks it and watch its indicator light, which should come on when the film moves away. If it doesn't, wipe the lens in one direction with a lint-free cloth soaked in isopropyl and test again. The sensor should sit as close to the film path as possible; adjust it with its two threaded rings.
-
Sensor or motor?
If the light still won't respond, unscrew the front ring, take the sensor out of its bracket and wave your hand in front of it. No light means the sensor has failed. If the light works but the reel still doesn't turn, the take-up motor is the likely fault. Contact us with what you found so we can send the right part.
-
Film won't move with the arrow keys
Power the printer off, leave it off for 5 minutes, then power on and try the up and down arrows again. If it still won't move, contact us. The next steps are a firmware reset in a password-protected menu and a check of the motor connector on the main board.
-
Pinch rollers won't lift
Look at the power supply for its blue light. If it's off, power off, wait 5 minutes and power on. If it's blinking, a connected part has a fault. In either case, if the rollers still don't move, contact us; we'll check the roller sensors, buttons and relay with you using the lights on the control board.
Loading checklist
- Handle the roll by its core only, printable side facing out, and tighten the right-hand holder.
- Route the film under the tension rod, then raise the rod fully.
- Lift the pinch rollers, feed the film across the bed and lower them. Release and reseat them once to even out the tension.
- Move the media guides in close to the film edges, but not tight against it. This helps prevent head strikes.
- Look from the front and the back to check the film lies flat.
- To unload, reverse the reel (2), release the rollers, support the roll as it winds so it stays even, and tape the loose end.
Never leave film buckled on the bed. Even a small bump that brushes the heads can leave residue that causes nozzles to drop out weeks later.
Watch DTF Station's video: troubleshooting the take-up sensor and motor on Prestige L series printers
Embedded from the manufacturer's official channel.
Common questions
What do the take-up switch positions mean?
On the XL2 Pro, XL3 and XL4: 1 is automatic with tension, 0 is off, and 2 reverses the reel for unloading. On the L2 and XL2 media motor, 1 advances the film and 2 rewinds it.
The film unwound itself overnight. What happened?
Usually the take-up or media motor was left on with no film tension, or the sensor read an empty path. Turn the take-up switch off when you aren't printing and remove the film for long breaks.
My prints are misaligned since I changed the roll. Is that a feeding problem?
Very likely. The take-up motor is often left off after a roll change. Turn it back on and reprint.
Can I clean the pinch rollers with alcohol?
No. Use a dry lint-free cloth, or one lightly dampened with water. Alcohol cracks the rubber.
My take-up sensor keeps wearing out. Why?
On L2 to XL4 printers, a tension bar bracket installed the wrong way round can wear the tension sensor early. DTF Station has a video on reinstalling it correctly.
- DTF Station technical documentation
- DTF Station video: Prestige L Series, How to Troubleshoot and Replace Take Up System Sensor and Motor
- DTF Station video: Prestige L2, XL2, XL3 and XL4, How to Troubleshoot Unresponsive Pinch Rollers
- DTF Station video: Prestige Large Format Printers, How to Adjust the Tension Bar Bracket
- DTF Station video: Prestige XL4, How to Load and Unload Media
- AA support requests about film feeding, take-up reels and pinch rollers on Prestige printers, 2024 to 2026











































































