Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige XL series ink leaks: dampers, tube connectors and ink filters
Most ink leaks on the Prestige large format printers come from a damper that has failed or isn't pushed fully onto its tube, a side tube that has worked loose, or an ink filter fitting. Power off, find where the ink is, and check those first. A leaking damper or filter is a simple swap, but always prime afterward so no air is left in the line. Leaks along the carriage tube bundle or inside the machine need parts and our help.
Match where the ink is
| Where you see ink | Most likely source | Go to |
|---|---|---|
| Dripping from the carriage or the print head, or ink on the head cables | A damper that has failed or isn't seated | Steps 2 and 3 |
| Ink smeared along the carriage rail | A slow leak in the tube bundle that travels with the carriage | Step 5 |
| Wet spot at the back, behind the rear panel | An ink filter fitting or tube connector | Steps 4 and 5 |
| Ink on the right side, around the side panel | A side tube or pump tube that isn't tightened, or is twisted | Step 1 |
| Ink around the bottles | Overfilling, a cap or a bottle valve | Step 1 |
| No visible leak, but one color keeps losing nozzles and the lines show bubbles | An air leak at a damper, filter or tube end | Steps 2 to 4 |
Ink on a circuit board or head cable can short it. If ink is dripping inside the carriage, stop printing, power off and clean it up before you do anything else.
Step by step
-
Check the easy connections first
Power off. Look at the bottles and their valves at the back, then open the right side panel and look at the side ink tubes. A side tube that has worked loose or twisted can weep at the joint. To refit one, pre-twist the tube a little counterclockwise, then reconnect it by turning clockwise so it rests straight with no twist. Wipe everything dry so you can see if the leak comes back.
-
Look at the dampers
Move the carriage to the center by holding the left arrow, remove the film and power off. Take off the carriage cover with a Phillips screwdriver. Every ink line should be pushed fully onto its damper. A damper is bad if ink leaks from it after a syringe is removed, if one line fills much more slowly than the others, or if bubbles keep appearing when you pull ink through it. To test one, hold it only by its hard plastic frame and pull gently with a syringe from the bottom. Solid ink means it's fine. Air or a steady stream of bubbles means replace it.
-
Replace a leaking damper
Clamp the ink line that feeds the damper so ink can't run out. Remove the old damper. If the end of the tube is stretched or split, trim it perfectly straight, as close to the damper as possible: an angled cut lets air in. Push the tube fully onto the new damper, unclamp, and prime it with a syringe until the damper fills and a little ink with no bubbles enters the syringe. Then press Enter to reset the carriage, run a cleaning (and a fill ink if needed) and print a nozzle check.
-
Replace a leaking ink filter (L2 and XL2)
The inlet filters sit behind the rear metal panel, held by a bracket with three screws. Power off, lay a towel underneath, and remove the panel and bracket. Each filter has twist-lock fittings: turn about a quarter turn to release it from the top tube, then from the bottom tube. Fit the new one with its inlet side facing up, toward the ink bottles, a quarter turn onto each tube. Refit the bracket and panel. A filter swap always lets some air in, so finish with the manual ink pull described in our poor nozzle check guide. On the XL2 Pro, XL3 and XL4, text us before opening the back so we can confirm the layout on your unit.
-
Leaks we fix with you
Some leaks need parts and a longer job: a leak in the tube bundle along the carriage, a cracked tube connector inside the machine, or ink coming from the capping station or pump. Replacing the full ink tube assembly takes hours and involves the head board, so we do it with you or on site.
Cleaning up after a leak
- Ink on the head, head cables or board: wipe with 99% isopropyl alcohol on a lint-free cloth and let it dry completely before powering on.
- Never use alcohol on the capping station caps, the wiper blade or the pinch rollers. It dries out the rubber.
- Ink is water based. Clean it off the bed and panels with cleaning solution and a lint-free cloth.
How often dampers and filters wear out
DTF Station treats dampers and ink inlet filters as yearly replacement parts on these printers. If your printer is more than a year old and one color keeps dropping out or weeping ink, plan on replacing that color's damper and filter rather than cleaning over and over.
Not sure where it's coming from? Text us a photo or short video at (562) 609-4996. Show the leak, the carriage and the back of the printer.
Watch DTF Station's damper test and replacement on the L2 and XL2
Embedded from the manufacturer's official channel.
Common questions
Ink is dripping from my print head. Is the head broken?
Usually not. Ink dripping at the carriage most often comes from a damper that has failed or a tube that isn't fully seated on it. Power off, clean it up, and check the dampers first.
Why does one color keep losing nozzles even though I can't see a leak?
An air leak lets air into the line instead of letting ink out. Check that color's damper with a syringe and look at the tube above and below its filter for bubbles. Bubbles near the filter point to the filter.
Can I cut the ink tube when I replace a damper?
Only to trim a stretched or split end, and only perfectly straight, as close to the damper as possible. An angled cut lets air in and causes the same problem again.
Which way does the ink filter go?
Inlet side up, toward the ink bottles. Afterward, do a manual ink pull to clear the air the swap let in.
Can I clean the leak with alcohol?
Use 99% isopropyl alcohol on the head and cables, but never on the caps, wiper blade or pinch rollers. Alcohol dries out rubber.
- Prestige L2 and XL2 Damper Test and Replacement (DTF Station video)
- How to Replace Dampers, Prestige L2 and XL2 (DTF Station video)
- Replacing Ink Filter, Prestige L2 and XL2 (DTF Station video)
- DTF Station technical documentation
- AA support requests about Prestige L2 and XL2 ink leaks, 2024 to 2026










































































