Support
Machine type
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

Switching a Prestige XL2, XL2 Pro, XL3 or XL4 to Color Prime Chroma ink

✓ Reviewed by Jason KimUpdated 2 min readFits: L2 · XL2 · XL2 Pro · XL3 · XL4 (CMYK channels)
Short answer

To switch to Color Prime Chroma, run your CMYK bottles low, syringe out what's left, then use Fill Ink (Ink Charge on the XL2 Pro, XL3 and XL4) to pull the old ink out of the lines. Fill with Chroma, prime the lines the same way, and run three cleanings back to back before a nozzle check. White isn't part of the change. If colors look off afterward with a full nozzle check, ask us to confirm your RIP print scheme.

Before you start

  • This procedure replaces the CMYK inks. White isn't part of it.
  • On the XL2 Pro and XL3, which also run light cyan, light magenta, green and orange, text us before you switch those channels so we can confirm the right inks and steps.
  • Run the printer until the CMYK bottles are as low as possible. Less leftover ink means less waste and an easier flush.
  • Have gloves, the syringe and tube from your printer's supply box, a waste container, paper towels and cleaning solution ready. The ink is water based and washes off, but dispose of it according to your local rules.

Step by step

  1. Empty the CMYK bottles

    Slide the tube onto the syringe (add extra tubing if you need the reach) and push it to the bottom of the bottle. Pull slowly and empty the syringe into your waste container. Don't pull hard: the syringe can pop off and spray ink. Rinse the syringe between colors and repeat for cyan, magenta, yellow and black.

  2. Clean the head area

    With the bottles nearly empty, clean around the print head, the capping station and the wiper blade with cleaning solution so no old ink is left there. Never touch the nozzle face.

  3. Pull the old ink out of the lines

    Open the lid and run Fill Ink on the color head (on the L2 and XL2 it's under Menu > Head Maintenance > Fill Ink; on the XL2 Pro, XL3 and XL4 use Ink Charge on the touchscreen or in Pilot). Watch the old ink move down the lines to the waste bottle and keep going until the lines are empty. This can take several minutes.

  4. Clear a color that won't drain

    If one color isn't moving, close the valves on all the other colors at the back. That makes the pump pull only from the stuck line. Open the valves again once it has drained.

  5. Fill with Chroma

    Shake each Color Prime Chroma bottle well, remove the cap tamper ring and fill each bottle as full as you can. Leave the bottle caps a quarter turn loose so air can get in.

  6. Prime and clean

    Run Fill Ink (or Ink Charge) on the color head again until the new ink reaches the head. Then run three head cleanings back to back and print a nozzle check.

  7. Finish up

    Clean the capping station and wiper blade once more. If a color is still patchy after a few cleanings, that color's damper may be due: older dampers are often replaced during an ink change. See our ink leaks and dampers guide.

Colors look different after the switch

A new ink can print differently with the same RIP settings. If colors look dull, or blacks don't look as deep as before, first confirm the nozzle check is complete on every color. If it is, the RIP's color profile is the next thing to check. Don't start changing ink limits or color settings at random: text us your RIP, your printer model and a photo of a test print, and we'll confirm which print scheme you should be using.

Stuck partway through? Text us a photo or short video at (562) 609-4996.

Watch DTF Station flush CMYK ink and fill Color Prime Chroma

Embedded from the manufacturer's official channel.

Common questions

Do I have to flush the old ink, or can I just top up with Chroma?

DTF Station's procedure removes the old CMYK ink from the bottles and lines before filling with Chroma, so the two inks don't mix. Follow the full flush.

Does the white ink change too?

No. This procedure covers the CMYK bottles only.

One color won't drain from the line. What do I do?

Close the valves on all the other colors at the back of the printer and run Fill Ink again. The pump then pulls only from the stuck line. Reopen the valves afterward.

My colors look duller since I switched. Is the ink bad?

Check the nozzle check first. If every color is complete, the RIP profile is the likely cause. Text us your RIP and printer model and we'll confirm the right print scheme.

What about light cyan, light magenta, green and orange on my XL3?

Text us before switching those channels. The DTF Station procedure is written for CMYK.

Sources
Did this fix it?