Support
Machine type
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

Prestige XL series daily and weekly maintenance: morning startup, end of day and weekly cleaning

✓ Reviewed by Jason KimUpdated 2 min readFits: L2 · XL2 · XL2 Pro · XL3 · XL4
Short answer

Every morning: circulate the white ink, run a short ink fill, do two head cleanings and print a nozzle check. Every evening: clean around the heads, the wiper blade and the caps, then wet the caps (by hand on the L2 and XL2, with the wet cap system on the XL2 Pro, XL3 and XL4). Every week: clean the encoder strip, rollers, vacuum holes and sensors, and empty the waste bottle.

Morning startup

L2 and XL2

  1. Power on and drain the caps

    Open the front cover, power on and wait for Idle. Press Cleaning once to drain last night's cleaning solution from the caps and let the cycle finish.

  2. Circulate the white ink

    Set the circulation knob on the side to 65 and press its power button for 5 minutes. Then turn it down to 10 to 20, or off.

  3. Short ink fill

    Go to Menu > Head Maintenance > Ink Fill > Two Head. Watch the drain line, and cancel once ink has been flowing steadily for about 5 seconds. Press Cleaning once more.

  4. Load film and check

    Advance the film so it covers all the vacuum holes, set the media guides, and print a nozzle check from Pilot.

XL2 Pro, XL3 and XL4

  1. Check ink and film

    Look at the ink alarm on the screen and top up any low bottles. Leave the caps loose so air can get in. Make sure the white ink stirring is running, the take-up motor is on and film is loaded.

  2. Circulate the white ink

    Set circulation to about 40% for 1 minute, then back to 20% or auto.

  3. Short ink fill, then two cleanings

    Run an ink charge for about 20 seconds and stop it. Then run Head Cleaning > Two Head All > Light twice. With the cover open, check that the capping station rises and the wiper blade touches the heads. If circulation was above 30%, add another cleaning.

  4. Nozzle check

    Check the print start position and print a nozzle check. About 95% complete is ready to print.

End of day (all models)

  1. Clear the film

    Feed out and cut any printed film, then reverse the film until it is clear of the rollers.

  2. Move the carriage out

    Press the left arrow once to lift the heads off the caps, then hold it to move the carriage fully left.

  3. Clean around the heads

    With a swab dipped in DTF cleaning solution, clean around each head's face plate. Don't touch the nozzle face itself. With a fresh swab, clean the wiper blade, the outer edges of the caps and any ink buildup nearby.

  4. Wet the caps

    L2 and XL2: pour cleaning solution into both caps until each has a slight dome. XL2 Pro, XL3 and XL4: press the wet cap button and check that solution fills the white cap.

  5. Park and cover

    Press Enter to dock the carriage on the caps. Wipe the bed with a lint-free cloth and isopropyl alcohol, and cover the printer.

Weekly

  • Encoder strip: 90% or stronger isopropyl on a lint-free cloth, wiped left to right.
  • Pinch and media rollers: dry lint-free cloth only, or lightly dampened with water. Remove the film first.
  • Vacuum holes and front heater: lint-free cloth and isopropyl, then let it dry.
  • Waste ink bottle: empty it, dispose of it under local rules, and make sure the tube goes back in.
  • XL2 Pro, XL3, XL4 also: clean the take-up sensor face and the paper sensor under the rear platen with isopropyl, and keep the wet cap bottle over half full with no air bubbles in its tube.

Monthly

  • Test the waste ink alarm. It runs on a battery, so replace the battery if the alarm is weak or silent.
  • If the carriage rail squeaks, grease it.

Water-based waste ink can be dried out (for example on scrap garments) or solidified with a water-based paint hardener, then thrown out as general waste. Always check your local rules first.

Watch DTF Station's video: full maintenance guide for the Prestige XL2 Pro

Embedded from the manufacturer's official channel.

Common questions

Can I use isopropyl alcohol on the rubber parts?

No. Alcohol dries out and cracks rubber. Use a dry lint-free cloth (or one lightly dampened with water) on the pinch rollers, and DTF cleaning solution on the caps and wiper blade. Isopropyl is for the bed, media guides, encoder strip, tension bar and sensors.

Should I leave the printer on overnight?

If you print every day, yes. Turn off the heater and vacuum but leave the printer on. It cleans itself every 4 hours and keeps the white ink moving. If you shut it down, make sure the heads are seated on the caps before you switch off.

How high should white ink circulation be?

Run it higher for a short time in the morning, then turn it back down. Left high, it pulls air into the white line. DTF Station's guideline is about 20%: just enough that you can barely hear the pump.

When is a nozzle check good enough to print?

When it is about 90 to 95% complete. Run one before each print and again after the printer has sat idle for 20 minutes or more.

What about the 6-month white channel service?

That is a separate, longer job. See our guide to white ink problems on the Prestige XL series.

Did this fix it?