Support
Machine type
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

Prestige XL series errors 013047 and 4000: print pass data unfinished, and carriage won't move at startup

✓ Reviewed by Jason KimUpdated 2 min readFits: L2 · XL2 · XL2 Pro · XL3 · XL4
Short answer

Error 013047, "Print pass data was unfinished", means the carriage starts a pass, freezes, and goes home a minute later without printing. When it's the only error, the usual cause is a print head ribbon cable shorted by ink or liquid. Error 4000 (often with 13023) shows up at power-on when the carriage won't move and you hear grinding, and points to firmware, the capping station sensor or the station itself. Read the code in Pilot, do the safe checks here, then contact us: the fixes need protected menus or opening the carriage electronics.

Both of these errors stop the printer cold, and both look worse than they usually are. The trick is reading the code correctly before anyone opens the printer. These steps are what you can check safely on your own; the repair itself we do with you on a call.

Match your error

Code What you see Usual cause
013047 only Carriage moves left, stops, returns home about a minute later. Nothing prints A head ribbon cable shorted by ink or liquid
013047 plus others Varies A different problem. Send us every code
4000 (often 13023) At power-on the carriage won't move and you hear grinding Firmware, capping station sensor, station mechanism or main board

Read the code

Open DTF Station Pilot and click the light bulb icon at the bottom right. Screenshot the full list of errors. Note exactly what the carriage did and when, and film it if you can.

Error 013047: what you can check

  1. Confirm it's the only code

    DTF Station's 013047 procedure only applies when 013047, "Print pass data was unfinished", is the sole error. Anything else on the list means a different diagnosis.

  2. Look for liquid

    With the printer off, open the top cover and look at the carriage for ink, cleaning solution or condensation dripping onto it. Wipe spills off the outside of the carriage with a lint-free wipe and isopropyl alcohol and let it dry. Don't open the board cover on the carriage.

  3. Get your firmware backup ready

    The first fix is a firmware reset using your own exported backup files, or DTF Station's default firmware if you have none. Find your backup files (they come as a pair) and tell us whether you have them.

  4. Contact us for the cable test

    If the reset doesn't clear it, the next step is unplugging the head ribbon cables and testing them one at a time to find the shorted one. It's done with the carriage cover off, where a carriage that docks too soon or a cable pushed in crooked can destroy parts, so we guide you through it live.

Error 4000: what you can check

  1. Stop the grinding

    Switch the printer off. Don't keep restarting it while the carriage grinds.

  2. Free the carriage

    With the power still off, turn the capping station knob to lower the station until the wiper blade is clear of the heads and the head strike sensor. Then push the carriage gently by hand to the middle of the bed.

  3. Power on and watch

    Turn the printer on and film what happens. If the capping station rises but the carriage still doesn't move, the capping station sensor is the likely cause. Either way, send us the video.

  4. Send your firmware version

    We'll ask for a screenshot of the firmware version from Pilot's Advance screen. Firmware is the first thing ruled out, then the sensor, its cable and finally the main board.

Before any firmware reset, your calibration and ink stack settings need to be photographed or exported. Loading default firmware without them wipes your printer's settings. That's why we do resets with you, not from a guide.

Prevent it

  • Keep bottles and cleaning solution off the top of the printer, and wipe up drips near the carriage right away.
  • Export a fresh pair of firmware backup files whenever settings change, and keep a copy off the computer. Our guide to moving NeoStampa and Pilot to a new computer shows how.

Text the screenshot and video to (562) 609-4996 and tell us which model you have.

Watch DTF Station's video: troubleshooting error 013047 (print pass data unfinished)

More videos

Troubleshooting capping station or motherboard error 4000 and 13023

Embedded from the manufacturer's official channel.

Common questions

Where do I see the error code?

In DTF Station Pilot, click the light bulb icon at the bottom right. Take a screenshot of the whole list.

Pilot shows 013047 and other codes too. Does this guide apply?

No. DTF Station's 013047 steps are only for when 013047 is the only error. Send us a screenshot of every code.

Can I reset the firmware myself?

Only with us. It's in a password-protected menu, and loading the default firmware erases your calibration and print settings unless they were saved first.

What causes a ribbon cable to short?

Usually ink or cleaning solution reaching the cables on the carriage. More than one cable can be affected.

Can I just keep power cycling until the carriage moves?

No. If the carriage grinds at startup, switch off and contact us. Forcing it can damage the station or the motor.

Did this fix it?