Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Seismo L16R or L24R belt stops, film not feeding, or touch screen goes dark
In Auto mode the belt stops by design whenever the sensor sees no film, and shaking stops 10 seconds later, so first check the mode and clean the film sensor. Creased film usually means the belt vacuum was left on after the take-up was taped. A belt that sticks often has powder bonded to it on the vacuum platform. A screen that shows the logo and then goes dark needs a firmware reset we can walk you through.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Belt and shaking stop when the printer pauses, then restart | Normal Auto mode behavior | Step 1 |
| Nothing moves even with film in place | Stop mode selected, or a dirty or blocked film sensor | Steps 1 and 2 |
| Film creases, wanders, or the head strikes it | Belt vacuum left on, or film not centered on the front plate | Step 3 |
| Film catches at the sub dryer | Sub dryer too low at the start | Step 3 |
| Belt drags or sticks once per rotation | Powder bonded between the belt and vacuum platform | Step 4 |
| Powder won't return or dispense | Damp or contaminated powder clogging the outlet | Step 5 |
| Take-up won't wind | Take-up switch off, film not taped, or cable loose | Step 6 |
| Screen shows the DTF Station logo, then goes dark | Screen firmware needs a reset | Step 7 |
Step by step
-
Check the mode
The mode keys are Manual, Auto and Stop, and only one can be on. Auto follows the film sensor. Manual runs continuously and ignores the sensor, which is useful for finishing the end of a roll. Stop halts powder, shaking and the belt while the heaters keep running, so a machine left in Stop looks dead even though it's hot.
-
Clean the film sensor
Turn the machine off. Brush powder away from the sensor, then wipe its face lightly with a lint-free cloth and isopropyl alcohol. Powder buildup here is the most common reason Auto mode stops responding.
-
Fix the film path
Pause the printer first. Center the film using the front heating plate, not the printer, as the reference, and make sure it lies flat against the plate without hanging past its edge. Once the film is taped to the take-up core, turn the belt vacuum off. If the film catches at the sub dryer, open it before you start, or adjust its height with its four screws.
-
Free a sticking belt
Turn the machine off and let it cool. Look for powder melted onto the belt or the vacuum platform under it. DTF Station warns that powder bonded there can glue the belt down as it cools, which can burn out the motor or warp the belt. Clean off what you can reach, keep the chamber cover closed while printing, and add powder gently. If the belt is torn or warped, contact us for the replacement belt.
-
Clear the powder supply
Empty and clean the powder box every day; damp powder clogs the outlet and strains the motor. If the outlet is clogged, remove and clean the powder brush. Sift any reused powder through a 60-mesh screen before it goes back in.
-
Check the take-up
Confirm the take-up switch is in position 1, the film is taped straight to the core, and the take-up cable is plugged in and locked. Apply light tension by hand if it winds too fast at the end of a roll.
-
Screen shows the logo, then goes dark
This is a known fault where the screen needs its firmware re-flashed from a Windows computer with a USB-C data cable and a reset tool from DTF Station. It means removing the screen panel with the machine unplugged. Text us and we'll send the tool and walk you through it. If the reset doesn't take, the screen itself gets replaced.
Unplug the machine before you open any panel. If the breaker trips, a motor smells hot, or the screen shows an error code, stop and contact us rather than resetting it repeatedly.
Send a short video of the problem to (562) 609-4996. It's the fastest way for us to tell which part is at fault.
Watch DTF Station's video: running the Seismo L16R and L24R
More videos
Embedded from the manufacturer's official channel.
Common questions
The belt stops every time the printer pauses. Is that a fault?
No. In Auto mode the belt stops as soon as the sensor stops detecting film, and powder dispensing and shaking stop about 10 seconds later. Everything restarts when film moves again.
Why did the temperature drop by 20 degrees on its own?
Auto standby heating. After about 20 seconds without printing in Auto mode, the shaker holds 20°C below your setting and returns to it when printing resumes.
How do I stop powder getting onto the belt?
Keep the shaker chamber cover closed while it runs and add powder slowly, without big movements. Powder on the belt can melt onto the vacuum platform and glue the belt down as it cools.
The screen is black but the machine hums. Can I replace the screen myself?
Text us first. Most of these screens come back with a firmware reset. If yours doesn't, we'll confirm the replacement screen and walk you through the swap.
- DTF Station: Seismo L16R user manual (PDF)
- DTF Station: Seismo L24R user manual (PDF)
- DTF Station: Seismo L16R and L24R operation guide
- DTF Station: Seismo L16R and L24R maintenance guide
- Seismo L16R user manual, 2023 edition (PDF)
- DTF Station technical documentation
- AA and DTF Station support requests about Seismo L16R and L24R belts, sensors, take-up and touch screens, 2024 to 2026











































































