Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige XL series warning lights and errors: power supply light, red carriage light, alarms and Pilot messages
A steady blue light on a power supply is normal; no light means the supply may have failed; a blinking light means a part connected to it has a fault. A red light inside the carriage, or a nozzle check that prints nothing at all, points to the head cables or board, so stop and contact us. Ink alarm lights mean that color is low. On older L2 and XL2 units, a "failed to load parameters" message in Pilot means the printer needs a board and firmware upgrade.
Match what you see
| What you see | What it means | What to do |
|---|---|---|
| Blue light on a power supply is steady | Normal | Nothing |
| Blue light is off | That power supply may have failed | Power off, wait 5 minutes, power on. Still off: contact us |
| Blue light is blinking | A part connected to that supply has a fault | Contact us. We'll walk you through finding which part |
| Red light inside the carriage (on the head board) | Head board or head cable error | Stop. Don't keep cleaning. Contact us |
| Nozzle check prints nothing at all | Usually cables or the head board, not a clog | Check the cover sensor, then contact us |
| A light on the ink alarm is flashing | That color is below the recommended level | Refill that color |
| Waste alarm sounds | Waste bottle full, or alarm battery low | Empty the bottle, test the alarm |
| Carriage stops suddenly (XL2 Pro, XL3, XL4) | Head strike sensor saw something in the carriage path | Check that the film is flat and nothing is on the bed |
| "Failed to load parameters" in Pilot (L2, XL2) | Older unit needs a board and firmware upgrade | Contact us |
| Pulse error after encoder strip work | Strip not seated in the encoder sensor | See our alignment and encoder guide |
Power supply lights
Each power supply has a blue light. The XL2 has two supplies stacked behind the back panel (24V on top, 42V below); the XL3 and XL4 have three (36V, 24V and 42V, top to bottom). The light only blinks when a connected part reports a fault, not just because a wire is loose. Finding which part is at fault means disconnecting and reconnecting cable pairs one at a time with the printer off, so we do that with you over a call.
Always power off before touching anything behind a panel. Take a photo of every cable and label before you disconnect anything.
No ink output at all
-
Rule out the cover sensor
The printer won't fire with the cover open. Make sure the center cover is fully closed and print the nozzle check again.
-
Look for the red light
Open the top cover of the carriage and look inside. A red light, especially a blinking one, means the head board has detected an error.
-
Contact us before going further
The next checks involve the head ribbon cables and board with the carriage cover off. A carriage that docks with its cover removed, or a damaged cable plugged into a good port, can destroy parts. We'll guide you through it step by step.
Ink and waste alarms
Each ink alarm light matches one color. Refill by matching the bottle cap label to the color. Shake white ink well and let it rest a few minutes before pouring, and leave the bottle caps loose afterward so air can get in. The waste ink alarm is battery powered. Test it monthly by turning the empty bottle upside down, and replace the battery if it doesn't sound.
For anything not listed here, text a photo of the screen or light, and the printer model, to (562) 609-4996.
Watch DTF Station's video: troubleshooting the power supply, ink alarm and control panel on Prestige printers
Embedded from the manufacturer's official channel.
Common questions
The power supply light is off. What should I try?
Power the printer off, wait 5 minutes and power it back on. If the blue light comes back steady, carry on. If it stays off, or starts blinking, contact us.
Is it OK to use the emergency stop to turn the printer off?
Only in an emergency. Using it routinely can cause power supply problems. Use the normal power switch.
Can I silence the ink alarm?
Yes, with the alarm switch, but turn it back on afterward or the printer won't warn you next time. The light clears by itself once you add ink.
Should I update Pilot or the firmware to fix an error?
Not on an L2 or XL2 without us. Some of these units are missing a board the update expects, and updating can leave the printer unable to start. Send us a screenshot of the firmware version first.
The touchscreen went dark. Is it broken?
On the XL3 it sleeps after 10 minutes without use. Tap it lightly to wake it. Never press hard.
- DTF Station technical documentation
- DTF Station video: Troubleshoot/Replace Power Supply Board, Ink Alarm, Sub Control Panel (Prestige)
- DTF Station video: Prestige L and R Series, Troubleshooting No Ink Output
- DTF Station video: Ink Alarm Feature, Prestige L2 and XL2
- AA support requests about Prestige XL series errors, no output and connection problems, 2024 to 2026











































































