Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige XL series cap tops and wiper blade: signs of wear, replacing an L2 or XL2 cap top, and what to order
Cap tops and wiper blades are wear parts that DTF Station expects to replace every 1 to 2 years. Clean them first, then watch a head cleaning: a torn, hardened or caked cap seal, or a nicked, bent or leaning wiper, means it's time. On the L2 and XL2 you can swap a cap top yourself with a magnetic screwdriver in a few minutes. Wiper blades and anything on the XL2 Pro, XL3 or XL4 capping station should be done with us, because their heights are set in protected software.
The capping station sits under the heads at the right end of the printer. Its cap tops seal against each print head so the pump can pull ink through during a cleaning, and keep the heads moist overnight. The wiper blade then sweeps the face of each head. Both are rubber, both touch ink every day, and both wear out. DTF Station plans on replacing them every 1 to 2 years.
Match your symptom
| What you see | Likely cause | What to do |
|---|---|---|
| Cap seal torn, cracked, hard or crusted | Worn cap top | Order a cap top. L2 and XL2: replace it below |
| Ink foams at the cap during a cleaning | Cap not sealing, or a loose tube | Steps 1 to 3 |
| Wiper nicked, bent or leaning | Worn wiper blade | Order the wiper, then text us |
| Wiper misses the heads or flicks ink | Wiper height | Text us |
| Cap sits off-center under the head | Carriage or cap position | Text us a video |
| Station won't rise, grinding, error 4000 | Station mechanism or sensor | See our XL error codes guide |
Check before you order
-
Clean everything first
A dirty cap looks worn. Press the left arrow once to lift the heads off the caps, then hold it to move the carriage left. With a foam swab and DTF cleaning solution, clean the cap tops, the rims around them and the wiper blade. Never use alcohol on the caps or the wiper: it dries out the rubber.
-
Look closely
With a flashlight, check each cap seal for tears, cracks, hard spots or dried ink that won't come off, and check the wiper edge for nicks, bends or a lean.
-
Watch a cleaning
Dock the carriage and run a head cleaning with the cover open. The caps should rise and seal on the heads without lifting the carriage, and the wiper should touch every head evenly without bending hard. Film it on your phone at eye level.
Replace a cap top (L2 and XL2)
DTF Station publishes this job for owners of the L2 and XL2. You need a magnetic screwdriver and the new cap top.
-
Power off and free the carriage
Turn the printer fully off. Open the printer cover and the front panel. Loosen the carriage release knob and slide the carriage by hand toward the middle of the printer so the capping station is fully exposed.
-
Remove the old cap
Take out the cap's mounting screws with the magnetic screwdriver so none fall into the station. Lift the cap straight up and pull off the ink tubes underneath.
-
Fit the new cap
Push the tubes firmly onto the new cap. Set it into the housing so it sits completely flush, with nothing pinched underneath, and refit the screws.
-
Test it
Power on and print a nozzle check from the control panel. If the check isn't clean, recheck that each tube is fully on and the cap sits flat, then run a cleaning and check again.
On the XL2 Pro, XL3 and XL4, and for any wiper blade, text us before you start. Wiper and cap heights live in a password-protected Pilot menu. Set too high, they wear the heads; set too low, cleanings stop working.
What to order
| Part | L2 and XL2 | XL2 Pro, XL3, XL4 |
|---|---|---|
| Cap top | Cap top for i1600 and i3200 printheads, one per head | Text us to confirm the cap for your heads |
| Wiper blade | Prestige L2/XL2 wiper blade assembly | Wiper blade for Prestige R Series, XL3/XL4 and Aries (XL2 Pro: text us) |
| Full station | i3200/i1600 capping station assembly for L2/XL2 | Capping station for the XL3 or XL4 |
Not sure which part is worn? Text us your nozzle check, the cleaning video and a close photo of the caps at (562) 609-4996.
Watch DTF Station change the cap top on a Prestige L2 or XL2
More videos
Embedded from the manufacturer's official channel.
Common questions
How long do cap tops and wiper blades last?
DTF Station's guideline is 1 to 2 years. Daily cleaning with the right fluid keeps them at the long end of that.
Can I clean the caps and wiper with alcohol?
No. Alcohol dries out the rubber on caps, wiper blades and pinch rollers. Use DTF cleaning solution on a foam swab.
Can I change the L2 or XL2 wiper blade myself?
DTF Station says to do it only when a technician asks you to. Order the wiper blade assembly and text us; we'll tell you whether it's needed and walk you through it.
My new cap top seems too thick to sit flat. What do I do?
Don't force the screws down. Make sure the tubes are fully on and nothing is trapped under the cap, then text us a photo of it next to the old one so we can confirm it's the right part.
The cap doesn't line up with the head. Is the cap worn?
Probably not. An off-center cap is a position setting, not wear. Text us a short video of the cap rising to the head.
- DTF Station: How to change the cap on the Prestige L2 and XL2
- DTF Station: Prestige L2 and XL2, how to change the wiper blade
- DTF Station: How to replace a wiper blade and set the wiper blade height in Pilot
- DTF Station: Prestige L2 and XL2 maintenance guide
- DTF Station technical documentation
- AA and DTF Station support requests about Prestige L2, XL2, XL3 and XL4 capping stations, 2024 to 2026










































































