Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Miro 24 maintenance: finishing the roll, end-of-day cleaning, weekly glycerin trays and monthly filters
At the end of each day, let the purifier run at least 5 minutes with the oven open, then wipe the chamber, the glycerin near the wiring side, the filter area, the platen, the media wheel and the sensor with isopropyl alcohol, and empty the powder tray into a sealed container. Clean both glycerin catch trays weekly. Replace the purifier filter, air vent filter and fabric top cover monthly.
Glycerin is the oily residue left behind as ink evaporates during curing. Most of it leaves as vapor, but some condenses inside the shaker. Left alone, it can pool around the wiring and soak the purifier filters, which then stop catching fumes. This routine keeps it under control. You need isopropyl alcohol, lint-free cloths, gloves and a brush.
Finish the roll first
-
Advance the last prints
In Pilot's Print tab, use the advance film button with an increment of at least 300 mm (300 to 500 mm is the recommended range), at a speed that matches the job's linear meters per hour.
-
Cut and feed slowly
When the pinch rollers stop, cut the film from the printer with a blade. Feed it into the powder station slowly and steadily so nothing under-cures. Turn off the take-up reel once the film reaches the shaking area.
-
Cure the tail
Let the last section drop into the powder station and leave it 1 to 2 minutes to cure. Turn the shaking down and off, and switch off preheat.
-
Roll it up
Wearing gloves (the film is hot), hold the film and turn the reel by hand or on low motor speed. Roll slowly so prints don't stick together, then remove the core.
End of every day
-
Cool it with the purifier
Open the main oven chamber. Turn everything off except main power, so the purifier keeps running, and let it run at least 5 minutes while the chamber cools. Then move the Miro 24 away from the printer, lower the preheating platen and turn off main power.
-
Wipe the oven
Wipe inside the heating chamber with isopropyl alcohol on a lint-free cloth and remove all glycerin. Pay extra attention to the side where the wiring connects to the body, where liquid tends to collect. Wipe the top surface and close the cover.
-
Filter area
Clean the outer filter cover, then open it and wipe any glycerin around the fan. Doing this daily makes both the fan and the filter last longer.
-
Powder station
Wipe the preheating platen with alcohol. Brush loose powder toward the bottom tray, working around the sensor without scratching it. Take out the media wheel, clean the wheel and rod, and gently wipe the sensor face.
-
Save the powder
Pull the bottom tray and pour the powder into a lidded container. Put the media wheel back, close the powder station and cover the whole shaker.
Weekly and monthly
| When | What to do |
|---|---|
| Weekly | After the daily routine, clean the glycerin catch trays on both sides with isopropyl alcohol and a lint-free cloth |
| Monthly | Replace the purifier filter, the air vent filter and the fabric top cover. Replace them sooner if they look yellow or feel damp |
| About every hour of printing | Check the powder and top it up |
Storing powder
Keep powder in a sealed container in a cool, dry room, around 70°F with humidity below 35%, out of direct sunlight. Powder stays good for about a year, but leaving it in the shaker contaminates it and can cause transfers to stick together on the reel. Keep used powder separate from new and mix it back in gradually. Never pour used powder back into the original bag.
Smoke while printing?
Smoke usually means the purifier isn't pulling. With the shaker cool, turn the power on, open the purifier chamber and check that the fan spins. Clean any glycerin around the fan motor. If the fan spins but smoke continues, a wet or yellowed filter is the usual cause. For a fan that won't spin, see our Miro smoke and purifier guide.
Built-in purifiers don't replace room ventilation. Keep a window open or a fan moving air, and wear gloves, eye protection and a mask when handling powder.
Text us a photo or short video at (562) 609-4996 if glycerin keeps building up faster than this routine clears it.
Watch DTF Station's Miro 24 daily, weekly and as-needed maintenance
More videos
Embedded from the manufacturer's official channel.
Common questions
What is the oily liquid inside my Miro 24?
Glycerin, a normal byproduct of ink evaporating during curing. Wipe it out daily so it doesn't pool near the wiring or soak the filters.
How often do I change the Miro 24 filters?
DTF Station recommends replacing the purifier filter, air vent filter and fabric top cover every month. Change them sooner if they are yellowed or damp.
Can I leave powder in the shaker overnight?
No. Empty the tray into a lidded container. Powder left in the shaker absorbs moisture and dust and can make transfers stick together on the reel.
How long do I cure the last section of film?
Let the final section sit in the powder station area for 1 to 2 minutes before turning the shaking off.
Should I use rubbing alcohol?
Use isopropyl alcohol on a lint-free cloth, as DTF Station's guides specify.
- DTF Station: Miro 24 maintenance guide
- DTF Station: Miro 24 operation guide
- DTF Station: Miro 24 operation manual
- DTF Station technical documentation
- AA support requests about the Miro 24, 2024 to 2026











































































