Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Prestige XL series and Aries Impact Stop error: head strike sensor, guard and film checks
Impact Stop means something pushed the head strike sensor guard, so the printer stopped the carriage to protect the head. Power off, flatten the film, and restart. If it keeps happening with nothing in the way, the guard is usually bent or sitting too low: straighten it, check its height, and clean ink off the sensors. If it still won't clear, the sensor cable needs checking with our help.
What Impact Stop means
Sensors on both sides of the carriage sit behind a thin metal guard. When the guard is pushed in, the printer assumes the head is about to hit something and stops the carriage instantly, with a beep and Impact Stop on the panel. The XL2 Pro, XL3 and XL4 also have a laser head strike sensor that watches the carriage path. It's switched on with the button below the touchscreen, so keep it on.
Match your symptom
| What you see | Likely cause | Go to |
|---|---|---|
| Impact Stop once, and the film is lifted or wrinkled | Film rose into the carriage path | Step 1 |
| Impact Stop at the same spot each time | A media guide, the wiper blade or the guard itself | Step 2 |
| Impact Stop right after power on, with nothing in the way | A bent guard holding the sensor pressed | Steps 3 and 4 |
| Thin streaks across the print, ink on the sensors | Ink residue or light head contact | Step 5 |
Step by step
-
Reset
Turn the printer off. Lift the pinch rollers, straighten the film so it lies flat with nothing rising, and lower the rollers. Turn the printer back on and wait for it to initialize and show Idle.
-
Find what hit the guard
If it happens again, note where the carriage stopped and look at what's touching the guard: the film, a media guide or the wiper blade. Take a photo before you move anything. It tells us a lot.
-
Straighten a bent guard
A bent guard can sit against the sensor and trigger it with nothing in the way. With the printer off, turn the capping station knob counterclockwise to lower the station and hold it there, then push the carriage to the middle of the bed. Loosen the two screws on the guard, slide it up and off, and gently bend it back into shape. Refit it and tighten the screws. You should see a small gap between the guard and the sensor.
-
Check the guard height
If the guard sits low enough to rub the bed or the media guides, raise it. DTF Station uses a quarter laid flat under the guard as a height reference: there should be a little space under the guard. Power on and check that the carriage docks on the capping station with no alarm.
-
Clean the sensors
Ink on the sensors causes false stops and streaks. Wet a swab or lint-free cloth with 99% isopropyl alcohol and clean the front and back of the sensor on each side, holding the sensor so it doesn't bend. To reach the far side, power off, lower the capping station with the knob and move the carriage to the center.
Stop it happening again
- Load film straight and flat. Bring the media guides in far enough to hold the edges down, but not tight against the film.
- Aries: keep tension on the B film feed rod low. Too much tension causes uneven lamination and head strikes.
- Pause the job right away if you see film lifting or bunching.
- Clean the sensors as part of your weekly routine.
A real head strike can leave film residue in the nozzles that shows up as dropouts days later, and a hard one can change the carriage height. If you've had one, tell us when you contact us, even if the printer seems fine.
Still stopping with the guard straight and nothing in the way? The sensor cable at the head board may need checking, which means opening the carriage covers. Contact us and we'll take you through it. Text us a photo or short video at (562) 609-4996.
Watch DTF Station troubleshoot the Impact Stop error
Embedded from the manufacturer's official channel.
Common questions
Is it safe to keep printing after an Impact Stop?
Yes, once you've found and cleared the cause. Reset by powering off, flattening the film and restarting. If it keeps coming back, work through the guard and sensor checks before printing more.
Why do I get Impact Stop when nothing is touching the head?
The guard can be bent so it rests against the sensor, or it can sit low enough to rub the bed or media guides. Straighten it and check its height with a quarter laid flat underneath.
What is the button below the touchscreen on my XL3?
On the XL2 Pro, XL3 and XL4 it switches on the laser head strike sensor that stops the carriage if something is in its path. Keep it on.
Can I clean the sensors with alcohol?
Yes. Use 99% isopropyl alcohol on a swab or lint-free cloth, front and back, and hold each sensor so it doesn't bend.
My printer had a head strike but the nozzle check looks fine. Should I worry?
Watch your nozzle checks over the next few days. Film residue from a strike can harden in the nozzles later. Tell us about the strike if dropouts start.
- Prestige and Aries: How to Troubleshoot Impact Stop Error (DTF Station video)
- DTF Station technical documentation
- AA support requests about Impact Stop on large format and Aries printers, 2024 to 2026










































































