Support
Machine type
Brand
DTF Station Aries 213 and Aries 113 UV DTF printers

Aries 213 and Aries 124 maintenance: end of day cleaning, weekly care and shutdowns

✓ Reviewed by Jason KimUpdated 3 min readFits: Aries 213 · Aries 124
Short answer

At the end of every day, clean around the print head (never the face), the wiper and the caps with UV DTF cleaning solution, then cap the head. Once a week, clean the encoder strip and print bed and empty the waste bottle. Use only UV DTF cleaning solution on ink parts: water-based DTF cleaner reacts with UV ink and clogs the heads. Wipe the heated roller with a dry cloth only.

Use only UV DTF cleaning solution on the head area, caps and wiper. Water-based DTF cleaning solution reacts with UV ink and clogs the heads. Never touch the print head face.

Every morning (Aries 124)

Power on and wait for Idle. Turn on white ink circulation (dial to 25) and the air compressor, and check the air pressure gauge on the left panel. Run two head cleanings back to back and print a nozzle check. If a head is missing nozzles, run Fill Ink on just that head for 30 seconds, cancel, run one cleaning and check again.

On the Aries 213, print a nozzle check before every print run and again after any pause of 20 minutes or more.

End of every day

  1. Move the carriage left and open the panels

    Hold the left arrow to move the carriage fully left, then open the left side panel (and the front panel on the Aries 124).

  2. Clean around the print head

    Dip a swab in UV DTF cleaning solution and clean under the carriage up to the edges of the head, not the face. Let solution soak any crust near the rim, then dry with a fresh swab or cloth.

  3. Clean the UV lamps (Aries 124 daily, Aries 213 as needed)

    Wipe the left and right lamps with a lint-free cloth and UV cleaning solution (on the Aries 213, isopropyl on a cotton swab), then dry.

  4. Clean the wiper and caps

    On the right side, clean the wiper blade with a swab and dry it with a paper towel. Don't rub a lint-free cloth directly on the wiper. Clean the rim of each cap and the whole top of the capping station. Soak heavy buildup first. On the Aries 124, finish by pouring a small amount of solution directly onto the caps.

  5. Cap the head

    Press reset (Carriage Reset on the 124) to send the carriage home, and check it seats properly on the caps.

  6. Switch off and cover

    Aries 213: turn off heating, vacuum, light, both take-up motors and the air filtration unit, close all panels and cover the printer.

Every week

  • Old film: turn off the take-up motor, cut the film and remove it.
  • Encoder strip: wipe gently with a lint-free cloth. Aries 213: isopropyl alcohol. Aries 124: UV cleaning solution. If it's scratched, dented or bent, don't clean it: it needs replacing.
  • Print bed: wipe the whole bed with a fresh lint-free cloth (isopropyl on the 213, UV cleaning solution on the 124).
  • Heated roller (Aries 213): dry lint-free cloth only.
  • Film sensor (Aries 213): lint-free cloth with a little isopropyl.
  • Waste ink bottle: pull the tube out with a cloth wrapped around it, empty the bottle and put it back.
  • Air filtration hose (Aries 213): loosen the connection, clean it, run the unit for 5 minutes, reconnect and clean the other end.

As needed

  • Rail: wipe off the old grease with a cotton swab, apply fresh rail grease evenly, and move the carriage left and right to spread it.
  • Air filtration filters: remove the 4 screws and the panel, swap the filters bottom to top, and reinstall. Arrows point up on the Aries 213 and down on the Aries 124.
  • Chiller (Aries 124): power the chiller off and pull it out, disconnect the cables, zip-tie the tubes so they don't leak, disconnect and drain all the water, reconnect, refill with 800 ml of distilled water only, and power on with the cap off to confirm flow before closing it.

Leaving it for more than a day

Aries 213, not used daily: move the carriage left, use a syringe to put UV DTF cleaning solution on the cap, send the carriage home, close the cover, press the emergency stop, confirm white ink circulation is on, and cover the printer.

Aries 124: daily users can power off. For 2 to 3 days, leave it on and turn off the air filtration, chiller, heating, vacuum and take-up motor. For a week, leave everything on and press the emergency stop, which keeps the circulation and stirring running.

Not sure about a step? Text us a photo or short video at (562) 609-4996.

Watch DTF Station's video: Aries 213 end of day maintenance

Embedded from the manufacturer's official channel.

Common questions

Can I use my regular DTF cleaning solution?

No. Use only UV DTF cleaning solution. Water-based DTF cleaner reacts with UV ink and causes clogs.

Can I clean the heated roller with alcohol?

No. Use a dry lint-free cloth only. Alcohol damages the rubber.

Foam swabs or cotton swabs?

The Aries 124 routine calls for cotton swabs, not foam. On the Aries 213, polyester swabs are used around the head.

I'm not printing for a few days. Should I turn it off?

Daily users can power off after the end of day clean. Aries 124: for 2 to 3 days, leave it on and switch off the air filtration, chiller, heating, vacuum and take-up motor. For a week, leave it on and press the emergency stop, which keeps white ink circulating.

Which way do the air filtration filters go?

On the Aries 213 the arrows point up. On the Aries 124 they point down.

Sources
Did this fix it?