Support
Machine type
Brand
DTF Station Aries 213 and Aries 113 UV DTF printers

Aries UV DTF errors: impact stop, 13047, carriage won't move, failed to load parameters, ink alarm

✓ Reviewed by Jason KimUpdated 2 min readFits: Aries 113 · Aries 213 · Aries 124
Short answer

Open Pilot and click the light bulb icon to see the exact error code first. Impact stop usually means the film or a media guide touched the head-strike sensor: power off, straighten the film and restart. 13047 (print pass data unfinished) usually points to a head cable that got ink on it. "Failed to load parameters" on an older printer usually needs a firmware update package. Most carriage errors need us on the line, so note the code and text us.

Match your symptom

What you see Most likely cause Go to
Impact stop on the panel, a beep, carriage stops dead Something touched the head-strike sensor Impact stop
Carriage moves left, stops, returns home after about a minute without printing. Error 013047. A shorted head ribbon cable Error 13047
Carriage stops mid-print, moves by hand while powered, or makes grinding noises Motor, belt, encoder or board Carriage problems
"Failed to load parameters" in Pilot Older printer needs updated firmware files Pilot errors
Beeping and a flashing red light Low ink alarm Top up the ink
Thin streaks across the print Ink on the head-strike sensor or under the carriage Impact stop, step 3

Impact stop

  1. Straighten the film and restart

    Turn the printer off, lift the pinch roller lever, straighten the film so it lies flat, lower the rollers and turn it back on. Wait for Idle.

  2. Find what hit the sensor

    If it happens again, note where the carriage stopped and look at what touched the sensor guard: raised film, a media guide, or the wiper blade. Take a photo for us.

  3. Clean the sensors

    Ink on the head-strike sensors also causes streaks across prints. Wipe the front and back of each sensor with a swab and 99% isopropyl alcohol, holding the sensor so it doesn't bend.

  4. Still happening with nothing in the way?

    The sensor guard may be bent or the cable may need checking. Contact us before you take covers off.

Error 13047 (print pass data unfinished)

Check in Pilot that 013047 is the only error. This error usually means one or more ribbon cables on the head board has shorted, most often because ink or another liquid got on it. Don't keep retrying the print. The fix is to reset the firmware, then test the cables one at a time, which means opening the carriage covers. Contact us and we'll take you through it and replace any shorted cable.

Carriage problems

Open Pilot and note any error codes. Then contact us with the code:

  • 00400, 013023, 01007, 01009: point to the head board.
  • 016004: encoder strip, encoder sensor or head board.
  • 1604 (also shown as 01604): belt tension or a bearing.

Things you can safely check yourself: open the side panel and see if the X motor has a red light (that points to the motor). Look at the encoder strip, the clear strip running behind the carriage: if it's dirty, clean it as shown in our maintenance guide. If it's scratched, dented or bent, it needs replacing.

If the capping station grinds, makes a new noise, or won't move up and down, stop printing and contact us.

Pilot errors

  • Failed to load parameters: printers built before December 2024 may need a motherboard upgrade package and new firmware files. Text us your serial number.
  • Pilot won't connect: try a different Ethernet cable or adapter. If it stays red, we'll help you change the network address.

When you contact us, have the error code, a photo or video of what the carriage does, and your serial number ready. Text us a photo or short video at (562) 609-4996.

Watch DTF Station's video: troubleshooting the impact stop error

Embedded from the manufacturer's official channel.

Common questions

Where do I see the error code?

In Pilot, click the light bulb icon at the bottom right.

The printer beeps and the red light flashes. What's wrong?

That's the low-ink alarm. Check the levels on the touchscreen and top up. On the Aries 213, press the silver button to mute it.

The carriage moves left but won't go right. Why?

That pattern usually means the home position sensor has failed. Contact us for a replacement.

White ink circulation won't turn on. What should I check?

Make sure the carriage is parked at home over the capping station, then turn circulation on again. If it still won't run, contact us.

Can I swap parts myself?

Some, with our guidance. Call or text us first so we can confirm which part is actually at fault.

Sources
Did this fix it?