Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Aries 213 and Aries 124 setup: filling UV ink, ink charge and your first nozzle check
Shake every UV ink bottle before you pour, and shake white and varnish for a full 60 seconds. Let the bottles rest a few minutes so the bubbles settle. After filling, turn on white ink circulation, run 2 to 3 short ink charges, then 2 head cleanings, and print a nozzle check. 90% or better and you're ready. If the same channel keeps missing, contact us.
Before you start
- Computer: a Windows 11 PC, not a Mac or tablet. Intel i5 or i7 at 2.6 GHz or faster, 8 GB of RAM or more, 500 GB free, and a wired Ethernet port (use an adapter on a laptop).
- Software: DTF Station Pilot (the printer driver) and NeoStampa (the RIP), with its dongle.
- Aries 124 only: the chiller filled with 800 ml of distilled water only, the compressor regulator set to about 20 PSI, and all shipping tape and brackets removed. Keep the carriage lock bracket in case you move the printer.
Fill the ink
-
Shake the bottles
Aries 213: shake each color 5 to 10 seconds, and white and varnish for a full 60 seconds, then let them sit 5 minutes. Aries 124: shake each bottle at least 20 seconds and white for 60 seconds, then let them sit at least 3 minutes. Resting lets the air bubbles rise.
-
Open the bottle with two holes
Make one hole to pour through and a second small one as a vent, so the ink pours smoothly.
-
Pour into the matching tank
Match each bottle to the label on its tank cap. On the Aries 124, make sure all the valves are closed before you fill, and leave the caps slightly loose afterward so air can flow. On the Aries 213, pour until the ink alarm light turns solid red, and check the levels on the touchscreen.
Charge the heads
-
Start white ink circulation
Aries 213: turn the circulation knob clockwise, run it in manual mode for 60 seconds or more, then switch to auto. Aries 124: set the dial to 25 and press the circulation power button.
-
Check the caps (Aries 124)
Move the carriage to the left and make sure each cap has a thin layer of clear liquid on top, then press Carriage Reset. Open all the ink valves at the rear ink bay.
-
Run ink charge
Run Ink Charge for about 30 seconds, then stop. Repeat 2 to 3 times. On the Aries 124 this is in Pilot under Settings, with Head Select set to all heads.
-
Run two head cleanings
Press Head Cleaning twice (on the Aries 124, Normal Cleaning on all heads).
-
Set the vacuum and air filtration
Aries 213: set the air filtration unit to 40 to 60% and start the bed vacuum at 5 for Color Prime film. Raise the vacuum only if the film slides.
-
Set the print start position
Open the cover and measure from the carriage rail to where the film starts, in millimeters, and enter it in Pilot under Settings > Media Settings > Print Start Position, then Save. On the Aries 124, 75 mm measured from the right film edge with the bed ruler is the usual starting value.
Print and read the nozzle check
Close the cover, make sure Pilot is connected, and print a nozzle check. A good pattern is a solid block of small, even dashes for every channel. UV DTF film is clear, so to read it, turn the bed vacuum off, slip a sheet of white paper under the film, then remove the paper and turn the vacuum back on.
| Result | What to do |
|---|---|
| 90% or more of nozzles printing | You're ready to print. |
| More than 10% missing | Run more ink charge cycles and cleanings, then check again. On the Aries 124, run 2 light cleanings on just the affected head. |
| The same channel missing every time | Stop and contact us. It may be the ink path or the head, and we'll test which. |
If an on-site installation is booked, don't run the head calibration yourself. The technician will do it.
Need help? Text us a photo or short video at (562) 609-4996.
Watch DTF Station's video: Aries 213 ink fill, ink charge and nozzle check
Embedded from the manufacturer's official channel.
Common questions
Can I run Pilot on a Mac or a Surface tablet?
No. Pilot needs a Windows 11 PC (not a tablet), with an Intel i5 or i7 at 2.6 GHz or faster, at least 8 GB of RAM, 500 GB free (SSD preferred) and an Ethernet port or adapter.
Pilot says "Failed to load parameters." What does that mean?
Printers built before December 2024 may need a motherboard upgrade and new firmware files to work with current Pilot. Contact us with your serial number.
Pilot won't connect to the printer. What can I try?
Try a different Ethernet cable or adapter. If the connection still shows red, text us and we'll help you change the computer's network address.
The printer is beeping and a red light is flashing. Is it broken?
That's the low-ink alarm. Check the levels on the touchscreen and top up. On the Aries 213, the silver button mutes it.
How do I set the print start position?
Measure from the carriage rail to where the film begins and enter it in millimeters in Pilot. For example, 6.5 cm is entered as 65. On the Aries 124, the usual value is 75 mm, measured with the bed ruler from the right film edge.
- DTF Station technical documentation
- DTF Station: Aries 213 ink fill, ink charge, nozzle check
- DTF Station: Aries 124 installation and setup
- AA support requests about Aries setup and Pilot connection, 2024 to 2026











































































