Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Which powder shaker to use with a Prestige L2, XL2, XL2 Pro, XL3 or XL4
The 24-inch XL2, XL2 Pro and XL3 pair with either the Miro 24 or the Seismo L24R. The XL4 should be paired with the Seismo L24R only, because it prints faster than the Miro 24's powder capacity can keep up with. The L2 pairs with the Miro 16 or Seismo L16R. The Seismo shakers need a 220V circuit; the Miro shakers run on 110V.
Which shaker fits which printer
| Printer | Shaker options | Why |
|---|---|---|
| L2 | Miro 16 or Seismo L16R (Miro 24 also handles 18-inch film) | 16-inch class film, up to about 17.7 to 18 in wide |
| XL2 | Miro 24 or Seismo L24R | 24-inch film, moderate speed |
| XL2 Pro | Miro 24 or Seismo L24R | 24-inch film, moderate speed |
| XL3 | Miro 24 or Seismo L24R | 24-inch film |
| XL4 | Seismo L24R only | Too fast for the Miro 24's powder capacity |
Plan the power and space
| Shaker | Max film width | Power | Powder |
|---|---|---|---|
| Miro 16 | 17.7 in | 1400W, 110V, 12.7A | Powder recycling every 4 to 5 hours |
| Seismo L16R | 18 in | 3500W, 220V, 16A | Recirculates, recycling every 4 to 5 hours |
| Miro 24 | 23.62 in | 1700W, 110V, 15.5A | About 1 kg, refill hourly |
| Seismo L24R | 23.62 in | 5200W, 220V, 24A | 4 kg, recirculates, refill every 3 to 4 hours |
The Seismo shakers need 220V. Confirm your circuit before delivery day. When you order film, make sure the roll is no wider than your shaker's maximum film width as well as your printer's. The Miro 24 takes four people to lift off its pallet and onto its stand.
Setting up a Miro 24 inline
-
Position it
Roll the Miro 24 to the front of the printer. Raise the preheating platen so the film touches it while printing, line it up with the center of the film (not the bed), and lock the wheels.
-
Prepare the media wheel
Measure your film width and set the media wheel to match. Tighten it only lightly; overtightening bends the rod.
-
Start heating and printing
Turn the shaker and preheating on, starting at 50°C. Send the print. When the film reaches the platen edge, pause, open the heating chamber and feed the film in.
-
Add powder and cure
When the image reaches the powder station, attach the media wheel, add powder up to the height of the wheel rod, close the chamber and resume. Turn on main heat (default 135°C) and shaking, then the take-up reel.
-
Finish the run
When printing ends, advance the film in Pilot in steps of 300 to 500 mm so the last prints pass through, let the final section cure 1 to 2 minutes, then roll it up slowly. Wear gloves; the film is hot.
End of day
Open the chamber and leave the built-in fume extraction running at least 5 minutes, turn off the heaters, wipe the chamber with isopropyl and a lint-free cloth, and return any unused powder to a sealed bag. Replace the Miro 24's filters monthly.
Watch DTF Station's video: running the Prestige XL2 Pro with the Miro 24
Embedded from the manufacturer's official channel.
Common questions
Why can't I use a Miro 24 with an XL4?
The XL4 prints up to 149 sq ft per hour. The Miro 24 holds about 1 kg of powder and needs refilling about every hour, so it can't keep up. The Seismo L24R holds 4 kg and recirculates excess powder.
Do I need an electrician?
For a Seismo L16R or L24R, plan on a dedicated 220V circuit. The Miro 16 and Miro 24 run on 110V; compare their current draw in the table above with your circuit. Have an electrician check before delivery.
What temperatures should I start with on a Miro 24?
Preheat at 50°C and raise it, up to 80°C, only if powder sticks where there's no print. The default curing temperature is 135°C. Adjust for your film and room.
How should I store powder?
In a lidded container, around 70°F, below 35% humidity and out of sunlight. Keep used powder separate and mix it in gradually with new.
Can I put an L2 with a 24-inch shaker?
The Miro 24 is built for both 18 and 24-inch widths, so it can run L2 film. Ask us which suits your volume.
- DTF Station technical documentation
- DTF Station video: Prestige XL2 Pro, Operating with Miro 24
- AA support requests about shakers paired with Prestige L and XL printers, 2024 to 2026











































































