Support
Machine type
Brand
DTF Station Prestige R1

NeoStampa basics for Prestige printers: new job, resize, nest and print

✓ Reviewed by Jason KimUpdated 2 min readFits: NeoStampa (DTF Station Edition) · Prestige R1 · R2 Pro · R2 upgraded to NeoStampa · L2 · XL2 · XL2 Pro · XL3 · XL4 · X6
Short answer

Click New Job, pick your printer and scheme, and add your files. Resize or rotate anything that sits in the red zone, copy and paste to fill the film, then click Nest with a minimal separation of 0.25 in. Click Print, make sure the connection is TCP/IP Port, choose Process and send simultaneously, and send. Save the job first (File > Save) if you'll want to reprint or edit it.

Before you start

  • The NeoStampa USB dongle is plugged in and its light is green.
  • DTF Station Pilot is open and its connection light is green.
  • Your printer driver and schemes are installed. If not, see our NeoStampa install guide first.

Pin NeoStampa to the taskbar (right-click its icon, Pin to taskbar) so it's one click away.

Build and send a job

  1. Start a new job

    Click New Job, select your printer and the scheme for the print quality you want, and click OK. Check that the media width under Predefined Sizes matches your film, for example 13 in.

  2. Add your art

    Click Add File, or drag files in from your desktop. Hold Ctrl to pick several at once.

  3. Size and rotate

    Select an image and use the scaling controls at the top to size it. Anything that hangs into the red zone is outside the print area: shrink it or click Rotate until it fits.

  4. Fill the film

    Select an image and use Copy and Paste (or Ctrl+C and Ctrl+V) for extra copies.

  5. Nest

    Click the Nest icon, set Minimal Separation to 0.25 in so there's room to cut, and click OK. NeoStampa packs the images tight to save film. Select everything and use the center icon if you want the layout centered.

  6. Print

    Click the Print icon. Confirm the connection is TCP/IP Port; if not, click Configure and choose it. For processing, DTF Station recommends Process and send simultaneously, especially on computers with less memory. Click Print and check the job shows up in the queue.

Save jobs for reprints

Each tab in NeoStampa is a separate job. To keep a job you can edit later, click File > Save before printing. That makes a CPS file. Double-click it any time to reopen the job with all images in place, then print again. Reopen it with the same scheme it was made with.

The connection setting decides what Print does. TCP/IP sends straight to Pilot. File saves a PRT file instead, which you open and print from Pilot. A PRT file can show a size of zero while it's still being written: leave it alone until it finishes.

Settings to leave alone, and ones you can change

Safe to adjust Leave at DTF Station's setting
White ink intensity and choke Ink configuration files
Highlight and white-related print options ICC color profiles
Rendering intent: Perceptual (default, most accurate) or Saturation (more vivid) Core color mapping, and halftone or textile options not used for DTF

To switch rendering intent, open the scheme settings, go to Color, change Perceptual to Saturation, save and print a test.

Don't install NeoStampa updates on your own. DTF Station checks each release for DTF and has found versions that cause white ink or choke problems. Close NeoStampa fully before running any installer, or it will fail.

Job won't send or colors look wrong? Text us a photo or short video at (562) 609-4996 with a screenshot of the print dialog.

Watch DTF Station's video: how to use NeoStampa (basic operation)

Embedded from the manufacturer's official channel.

Common questions

NeoStampa shows an error under Status. What does it mean?

NeoStampa can't talk to Pilot. Open Pilot and make sure its connection light is green, then resend.

Why does white in my artwork disappear on screen?

Set your media profile's color to RGB 105, 105, 105, a charcoal gray, so white areas don't blend into the canvas.

Do I have to type the film width every time?

No. Under Predefined Sizes, create a media profile for each film width you use, named by size, and pick it when you start a job.

Can I rename a print scheme?

Yes, but open it in NeoStampa and use Save As with the new name. Renaming the scheme file in its folder can corrupt it.

Did this fix it?