Support
Machine type
Brand
Epson SureColor F170

Shipping or moving a printer for service: how to pack it safely (Epson and DTF Station)

✓ Reviewed by Jason KimUpdated 3 min readFits: Epson F2270 · F570 · F170 · DTF Station Prestige printers
Short answer

Don't ship a printer until we or the manufacturer tell you where it's going and how. When you do, keep it level, leave the ink installed unless you're told otherwise, lock the head and carriage the way the maker describes, and pack it in its original box or crate with the original packing. Epson and DTF Station both exclude damage caused by poor packing, and Epson bills you for it.

Before you pack anything

  1. Talk to us first

    Text (562) 609-4996. Many problems are fixed without shipping, and warranty repairs are often done on site, by exchange or with parts shipped to you. If a printer does need to travel, we'll confirm where it's going and how.

  2. Get the paperwork

    DTF Station won't accept a return without a Return Merchandise Authorization (RMA) number. For an Epson exchange, Epson's carrier picks up the old printer, and you use the shipping information that comes with the replacement.

  3. Find the original packing

    Both Epson and DTF Station ask for the original packaging or an equivalent that protects against shock and vibration. DTF Station strongly recommends the original crate for return shipments, so keep it if you can.

Epson's warranties exclude damage from improper packing or shipping, and Epson bills you for it. DTF Station's warranty excludes transit damage caused by the owner's packaging. A good pack job protects your claim.

Rules for every printer

  • Keep it level. Never tilt it, stand it on end or turn it upside down, or ink can leak.
  • Leave the ink installed on Epson printers. On the F2270, removing the ink packs can clog the nozzles or cause leaks.
  • Lift with enough people: four for the F2270, at least two for the F570.
  • Remove paper, film or platens, close all covers and disconnect every cable.

Epson F2270

  1. Prepare the platen area

    Lift off the platen. Loosen the fixing lever, set the platen gap lever to 8, then tighten the fixing lever to lock it.

  2. Lock the base

    Turn the printer off and disconnect the cables. For a move to another floor or building, slide the moveable base by hand to the transport position shown in the User's Guide and refit the carriage lock you removed at setup, with its screw.

  3. Deal with the waste ink

    Remove the waste ink tube from the bottle and remove the bottle. Take off the rear cover, pull out the waste ink tubes, wipe the outlets and fit the outlet caps from setup. Wear the gloves from the maintenance kit.

  4. Pack it

    Use the packing materials it came with. If it will sit unused in transit for more than two weeks, do Epson's storage preparation first.

After the move, refit the rear cover, waste tubes, bottle and platen, then run a nozzle check and a print head alignment.

Epson F570

Epson's F570 steps cover short moves, such as between floors of the same building. For a long-distance shipment, Epson says to contact Epson for support. For a short move: remove the paper, open the ink tank cover and caps, remove the transportation cap, flip it and insert it in the transport position, close the ink tank caps so they lie flat, turn off and unplug the printer, disconnect cables, and close all covers. Two people lift it by the handholds, or roll it on the optional stand on a level floor with the casters unlocked. After the move, return the transportation cap to the printing position: the printer can't print with it in the transport position.

Epson F170

  1. Power off the right way

    Turn it off with the power button and wait until the power light goes out before you unplug it, so the print head returns home and doesn't dry out.

  2. Secure the head and ink

    Disconnect the cables and remove the paper. Open the printer cover, tape the print head to the case, make sure the ink tank caps are on tight, and close the ink tank cover and the printer cover.

  3. Pack it

    Put the printer in its plastic bag and pack it in the box with the protective materials.

DTF Station Prestige printers

DTF Station's return procedure is: contact DTF Station or us, provide proof of purchase, the serial number and a description of the issue, get an RMA number, pack the printer securely in its original or equivalent packaging, and ship it to the address DTF Station gives you. For a refund return, DTF Station expects the printer back complete, with all original components and accessories.

Refit any transport brackets or locks that came off at setup. On the Prestige R1, that's the carriage L-bracket. Because preparation differs by model, text us before you pack a Prestige and we'll walk you through the steps for yours.

Watch Epson's video: SureColor F2270, repacking the printer

Embedded from the manufacturer's official channel.

Common questions

I threw away the original box. What now?

Epson and DTF Station both accept equivalent packaging that protects the printer from shocks and vibration. Text us before you pack and we'll help you work out what will do.

Epson sent me a replacement printer. What do I do with the old one?

Pack it in the same or equivalent packaging and return it using the shipping information that came with the replacement. Epson's terms give you seven business days (five working days for the F170 exchange), or you're charged for the replacement.

Can I tip the printer on its side to fit it in my car?

No. Epson says never tilt it, stand it on end or turn it upside down, because ink can leak. The F2270 shouldn't be tilted more than 10 degrees even when moving it across a room.

Do I need to drain the ink first?

Not on the Epson printers in this guide: Epson says to leave the ink installed. For DTF Station printers, ask us first. We'll tell you what to do for your model.

Did this fix it?