Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Miro 24 setup: uncrating, stand assembly, take-up reel and the first run with your printer
Use four people to lift the Miro 24 off its pallet and onto the stand. Build the stand from the numbered panels, fit the take-up arms and poles with the motorized end on the right, plug in the motor cable and center a paper core. For the first run, center the preheating platen on the film, preheat at 50°C (up to 80°C if needed), cure at 135°C and keep the powder below the media wheel rod.
The Miro 24 ships in a crate with its stand in pieces. Plan on four people for the two lifts (off the pallet and onto the stand). Have a snap blade, a power drill, flathead and Phillips screwdrivers, scissors and gloves ready. Wear the gloves the whole time: the crate has sharp metal edges.
Uncrate it
-
Release the blue locks
Pop each blue lock out with a flathead screwdriver and pull it free. Work around the top lid, lift the lid off, then do the same for each of the four side panels.
-
Remove the supports
Unscrew and remove the two metal crossbars at the base (two screws at each end) and undo the Velcro straps, two on each side.
-
Lift it off the pallet
With four people, lift the shaker off the pallet. Unscrew and remove the two wooden crossbars underneath it.
-
Lay out the parts
Open the accessory box and set every part on the floor with its number label facing up. Cut the plastic wrap off the machine, open the shaker lid and take out the accessories packed inside.
Build the stand
-
Pre-assemble the hardware
Put a washer on a bolt, push it through a panel hole and start a wing nut loosely on the other side. Do every hole on both #4 panels, the #5 panel and the #9 panel. That is 16 sets in all.
-
Attach the panels
Unfold the two legs of the #2 base and turn the casters inward. Turn the wing nuts upright, slide them into the grooves and tighten. Fit a #4 panel on each short side, the #5 panel on one long side and the #9 panel on the other.
-
Finish the cabinet
Flip the stand onto its casters and lock all of them. Open the doors and slide the #3 panel in so it rests on the ledge as the storage floor.
-
Mount the shaker
With four people, lift the shaker onto the stand and line its feet up with the mounting holes.
Install the take-up reel
-
Fit the arms
Take the thumb screws out of the shaker body. The left and right arms are told apart by which way their thumb screws face (up). Start all four screws on one arm loosely, then tighten them fully. Repeat on the other side.
-
Fit the poles
Loosen the thumb screws on both arms. Slide the back pole all the way in first, then feed the front pole through the rear opening. Slide the non-motorized reel end onto the poles first and seat the motorized end on the right arm. Tighten two thumb screws on each arm.
-
Connect and load a core
Plug the take-up motor cable into the shaker body and tighten its connector nut. Push a paper core into the reel, center it, and lock it with the thumb screws.
First run with your Prestige
DTF Station's operation guide shows the Miro 24 in front of a Prestige L series printer. Start only after the printer's daily maintenance is done and its nozzle check is clean.
-
Position it
Roll the Miro 24 to the front of the printer and raise the preheating platen. Use its adjusting screws so the film touches the platen while printing. Center the platen on the film, not on the printer body, then lock the wheels.
-
Set the media wheel
Take the media wheel out of the powder station, measure your film width and set the wheel to it. Tighten it only part way so it can still slide sideways. Overtightening bends the rod.
-
Preheat
Turn on the Miro 24 and its preheating. Start at 50°C and raise it gradually, up to 80°C, only if powder won't release from the unprinted film. Preheat drives static and moisture out of the film.
-
Feed the film in
Send the job and pause the printer when the print reaches the edge of the preheating platen. Open the heating chamber, feed the film in, hold it down with the supplied clamps and pull it gently toward the back. Resume printing. Wear gloves if the chamber has been on.
-
Start powdering and curing
When the print reaches the bottom of the powder station, pause again. Seat the media wheel in its groove, pour a small amount of powder into it, pull the clamp to the oven edge, then close and lock the chamber. Resume, then turn on main heat and shaking. The curing default is 135°C; adjust it for your film and room. Set shaking intensity with the control knob.
-
Attach the take-up reel
Keep the film straight by guiding it from the back until it reaches the take-up motor. Remove the clamps once there is slack, run the film under the tension rod, tape it to the core and switch on the take-up motor. Then top up the powder, never higher than the media wheel rod.
Stay with the machine the first few times you run it. Check the powder level, the curing temperature and the finished transfers as you go.
Film walking to one side, the paddle not reaching the film, or the reel pulling too much film? Text us a photo or short video at (562) 609-4996 and we'll help you adjust it.
Watch DTF Station install the Miro 24 step by step
More videos
Embedded from the manufacturer's official channel.
Common questions
How many people do I need to set up the Miro 24?
Four, for lifting it off the pallet and again for lifting it onto the stand.
Do I center the Miro 24 on the printer or on the film?
On the film. Line the middle of the preheating platen up with the middle of the film, then lock the wheels.
What temperatures should I start with?
DTF Station's guide starts the preheat at 50°C, raising it up to 80°C only if powder sticks to the unprinted film, and cures at 135°C. Adjust for your film and room.
How much powder should I put in?
A small amount to start, then top it up to no higher than the media wheel rod. Overfilling causes film tension problems.
Which side does the take-up motor go on?
The motorized end of the reel sits in the right arm. The non-motorized end slides onto the poles first.
- DTF Station: Miro 24 quick start guide (initial setup)
- DTF Station: Miro 24 operation guide
- DTF Station: Miro 24 operation manual
- DTF Station technical documentation
- AA support requests about the Miro 24, 2024 to 2026











































































