Support
Machine type
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

Prestige XL series idle time and storage: overnight, weekly use, and breaks of 2 weeks or more

✓ Reviewed by Jason KimUpdated 1 min readFits: L2 · XL2 · XL2 Pro · XL3 · XL4
Short answer

Prestige printers stay healthiest switched on and parked on wet caps, because they clean themselves every 4 hours and keep the white ink moving. For a break of 2 weeks or more, do the full daily and weekly maintenance, leave the printer on with circulation on auto, top up the cleaning solution, take the film off, switch off the take-up motor and cover the printer. Opened ink keeps for about 6 months.

Pick your situation

How long What to do
Overnight, printing daily End-of-day cleaning, wet the caps, leave the printer on with heater and vacuum off
A few days between jobs, printing weekly Same, plus turn off the heater, vacuum, ink alarm and take-up switches
2 weeks or more Full storage steps below
Moving the printer Contact us first

Overnight

Do the end-of-day routine: clean around the heads, the wiper blade and the caps, then wet the caps (by hand on the L2 and XL2, with the wet cap system on the XL2 Pro, XL3 and XL4). On the L2 and XL2, hold the power button on the touchscreen until it goes dark, which turns the heater and vacuum off while the printer stays on. Left like this, it cleans itself every 4 hours and circulates white ink. The XL2 Pro, XL3 and XL4 also wet the white caps automatically after 2 hours idle, as long as the cleaning solution bottle is at least half full.

Breaks of 2 weeks or more

  1. Do a full clean

    Complete the daily and weekly maintenance: heads, wiper, caps, encoder strip, rollers, bed and sensors. Empty the waste bottle.

  2. Set circulation and stirring to auto

    Leave white ink circulation and agitation on auto so the white keeps moving while you're away.

  3. Top up, but don't overfill

    Fill the ink bottles partway (DTF Station's guidance is about half to 60% full) and fill the cleaning solution bottle that feeds the wet caps.

  4. Take the film off

    Remove the film and store it somewhere cool and dry. Turn the take-up motor off.

  5. Leave it on and covered

    Leave the printer powered on, parked on its caps, with the cover on. A printer that stays on keeps running its own cleanings.

Coming back

Run the normal morning startup: drain the caps, circulate the white ink, run a short ink fill and two cleanings, then print a nozzle check. If channels are missing, work through our poor nozzle check guide before printing production work.

If the printer lost power for days (for example in an outage), it couldn't clean itself. Expect a longer recovery, and text us your first nozzle check at (562) 609-4996 if it doesn't come back after two rounds of ink fill and cleaning.

Where to keep it

Keep the room away from high heat, cold and direct sunlight. DTF Station recommends 70 to 75°F and 35 to 45% humidity.

Watch DTF Station's video: storing the print head on the Prestige L2 and XL2

More videos

Wet capping the Prestige XL2
Prestige XL2 closing procedure
Prestige L2 and XL2 daily maintenance
Prestige L2 and XL2 weekly maintenance

Embedded from the manufacturer's official channel.

Common questions

Is it better to turn the printer off when I'm away?

No, not if you can avoid it. Left on and parked on the caps, it runs its own cleanings and white circulation. A printer that is fully off gets neither.

What if I have to switch it off?

Make sure the heads are seated on the caps first, then power off normally (not with the emergency stop). Expect to run extra ink fills and cleanings when you come back, and contact us if the nozzle check doesn't recover.

How long does ink last?

Opened ink is usable for about 6 months. Keep it in its original bottle, capped, out of heat and sunlight.

Should I take the print heads out for storage?

Only if we ask you to. Removing and storing heads is a technician-guided procedure.

I need to move the printer. What should I do?

Contact us first. You'll need the carriage lock bracket that was removed at setup, and heads can be knocked out of position in transit.

Sources
Did this fix it?