Support
Machine type
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)

Prestige XL series white ink problems: missing white nozzles, bubbles and the 6-month white service

✓ Reviewed by Jason KimUpdated 2 min readFits: L2 · XL2 · XL2 Pro · XL3 · XL4
Short answer

White ink is heavy and dries faster than color, so it is the first channel to drop out. Keep circulation low in normal use (high circulation pulls air into the line), make sure the white cap is getting cleaning solution, then run a short ink charge on the white head and a cleaning. Hot, dry rooms and fans blowing on the printer are common hidden causes. Every 6 months, the white tank and lines need a full clean-out.

Match your symptom

What you see Most likely cause Go to
White rows missing on the nozzle check Dry white cap, settled ink, partial clog Steps 1 to 3
Bubbles in the white ink tube Circulation set too high Step 1
White fades during a job Airflow on the heads, hot dry room Step 4
Circulation pump doesn't run Carriage not parked, or a switch, board or pump fault Step 5
White still weak after all of the above Thickened ink in the tank, lines and dampers 6-month service below
Nozzle check fine, but white thin or showing past the edges on transfers RIP white settings Our neoStampa guides

Step by step

  1. Set circulation correctly

    Run circulation high only briefly in the morning: on the L2 and XL2, knob at 65 for 5 minutes, then down to 10 to 20; on the XL2 Pro, XL3 and XL4, about 40% for 1 minute, then 20% or auto. On the L2 and XL2, run a cleaning before you start circulation. Left high all day, it pulls air into the white line. A good working level is where you can barely hear the pump.

  2. Make sure the white cap gets solution

    Check that the cleaning solution bottle is at least half full and that the tube to the white cap has no air in it. On the XL2 Pro, XL3 and XL4, move the carriage left and press the wet cap button (on the XL4 it's beside the carriage, behind the left side covers). Solution should flow and fill the white cap. If you can't see any, press it once or twice more. On the L2 and XL2, fill the caps by hand each night.

  3. Recover the white head

    Return the carriage home. In Pilot, run an ink charge on the white head (H2) for 10 seconds or more, stop it, then run a normal cleaning on H2. Print a nozzle check. Aim for about 95%. If white still won't come back, follow the warm wet cap and ink pull steps in our poor nozzle check guide.

  4. Check the room

    Hot weather and low humidity are hard on white, and a fan or air conditioner blowing on the printer can dry the white nozzles within minutes of printing. DTF Station recommends 70 to 75°F and 35 to 45% humidity.

  5. If the circulation pump won't run

    Make sure the carriage is parked in its home position over the caps, then switch circulation on again. If it still doesn't run, the cause is usually the home sensor, the circulation switch or knob, the control board or the pump motor. Contact us and we'll help you narrow it down.

The 6-month white channel service

Over time white ink thickens and builds up in the tank, tubes, dampers and nozzles. Every 6 months, DTF Station has you:

  • Close the white valve, disconnect the white tank and its stirrer, and empty it.
  • Rinse the tank and stirrer with water until clean, keeping electrical connectors dry, and let everything dry fully.
  • Run circulation to push the old ink out of the lines until only air flows.
  • Refit the tank, fill it with fresh, well-shaken white ink, circulate, then fill the white head only for about a minute and run two cleanings.

The video above walks through every screw and connector. Watch it in full before starting.

If any connector gets wet, let it dry for 24 hours or wipe it with isopropyl before you power on.

Watch DTF Station's video: 6-month white channel maintenance on the Prestige L2 and XL2

Embedded from the manufacturer's official channel.

Common questions

Why does white go missing when color is fine?

White ink contains heavy pigment that settles and dries faster than color. It needs regular circulation, a wet cap at night, and a room that isn't hot and dry.

I see bubbles in the white ink tube. Is that bad?

Bubbles in the tube usually mean circulation is set too high. Turn it down. Some air inside the damper body is normal; air in the tube above it isn't.

The white looks fine on the nozzle check but thin or patchy on the transfer. Is it the printer?

Often not. White strength and how far the white is pulled in from the edges are set in the RIP. See our neoStampa guides, and check your film and powder.

How should I prepare new white ink before refilling?

Shake the bottle well, then let it sit a few minutes so the bubbles settle before you pour.

Do I have to do the 6-month white service myself?

It is a hands-on job of about an hour or more, with tubes and wiring to disconnect. Watch the video first. If you'd rather not, contact us.

Sources
Did this fix it?