Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool Apparel Printer and OS1 transfers peeling, cracking or creased: heat press settings and technique
For xTool PET film on 100% cotton, xTool recommends 160°C (320°F) for 6 seconds, peeling only after the transfer cools below 100°C (212°F), then pressing again with the same settings. On large designs, re-press each edge and corner in the middle of the platen. Most peeling after washing comes from too little heat or pressure at the edges.
When a transfer from the Apparel Printer and OS1 peels, cracks at the edges or comes out creased, the cause is usually the press step, not the oven. These are xTool's own pressing instructions for its PET film.
xTool's settings for 100% cotton
| Step | Setting |
|---|---|
| Pre-press the garment | Same temperature as the transfer, about 5 to 6 seconds |
| Press | 160°C (320°F) for 6 seconds |
| Peel | After it cools below 100°C (212°F), about 10 to 20 seconds |
| Re-press | Same settings again, with the film removed |
For other fabrics, xTool points to its Smart Press settings on the Atomm website. Longer is not always better: each fabric has its own time and temperature.
Step by step
-
Use a firm, even base
xTool recommends a heat press mat large enough for the garment and design, and a foam type to even out pressure. If your press pad is too soft, xTool suggests a thick magazine under two layers of towel as a firmer base.
-
Trim the film
Cut away excess PET film around the design. A big sheet around a small design can bunch up and press creases into the print.
-
Pre-press
Press the garment alone for 5 to 6 seconds to drive out moisture and wrinkles.
-
Press the transfer
Place the design inside the working area of your press and press at your settings. xTool recommends a protective sheet such as parchment or butcher paper on top for more even heat.
-
Let it cool before you peel
Do not peel straight away. Wait until it is below 100°C (212°F), then peel gently.
-
Press it again
Run a second full press with the same settings. xTool strongly recommends this for durability.
-
Re-press the edges on big designs
Most presses give less pressure at the edges. Move each corner and edge of a large design into the middle of the platen and press it again with the same settings.
-
Cool down
Let the garment cool completely to room temperature.
Match your symptom
| Problem | What to change |
|---|---|
| Peels right after pressing | Temperature too high or too low, too little pressure, too little time, or a soft pad |
| Peels after washing | Re-press edges and run the second press; wash below 60°C (140°F) |
| Small text or thin lines lift | Re-press with a little more time or temperature |
| Design creased, shirt smooth | Foam mat, trim the film, or a design too big for the platen |
| Warps or peels on canvas or linen | Coarse weaves bond poorly; xTool suggests a tighter weave |
| Colors fade after washes | Some fading is normal with water-based ink |
xTool rates properly applied transfers for 50 normal washes. If the cured film itself comes out of the oven warped or wavy, that is an oven problem: see our OS1 curing guide, or text us a photo at (562) 609-4996.
Common questions
Hot peel or cold peel?
xTool says to wait until the transfer is below 100°C (212°F), usually 10 to 20 seconds, then peel.
Do I really need a second press?
xTool strongly recommends it. After peeling, press again with the same settings for maximum durability.
How many washes should a transfer last?
xTool rates properly applied transfers for 50 normal washes. Avoid washing above 60°C (140°F).
Should I use parchment or butcher paper?
Yes. xTool recommends a protective sheet for more even heat.











































































