Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool OS1 errors: Misalignment, printer not recognizing the oven, and oven won't power on
For a Misalignment error, trim and realign the film, brush the film detection sensor, restart both machines and run Device self-check, then redo Alignment calibration. If the printer only shows its own icon, look for the blue sensor light inside the oven: lit means a data cable or wiring problem, dark means a power problem such as the fuse in the power switch. Internal board and power supply checks are for us, not for owners.
Three problems account for most OS1 error calls: a Misalignment error during the film hand-off, the printer not seeing the oven, and the oven not powering up at all. Start by checking which one you have.
Match your symptom
| What you see | What it means | Go to |
|---|---|---|
| "Misalignment" on the panel or in the software | Film hand-off from printer to oven failed | Misalignment |
| Printer shows only the printer icon, sensor inside oven is lit blue | Oven is on but not talking to the printer | Not recognized |
| Printer shows only the printer icon, sensor inside is not lit | Oven has not booted | No power |
| Clicking from the oven, "Printer film jam" | Real jam | Our film jam guide |
To check the blue light, look through the inspection window on top of the oven: the sensor in the bottom-left corner should glow blue when the oven is running.
Misalignment
The error can come with a code such as nailCheckError, baffleUpError, filmArriveError, holeNailAdapterTimeOut or filmFall. Work through these in order.
-
Fix the film
Cut off any wrinkled, creased or damaged film. Pull the film taut and line its edge up with the white marking line, within 1 mm and not overlapping it.
-
Clean the film detection sensor
Lift off the magnetic cover, brush the sensor with the supplied brush, tap its housing to shake out packed powder, and brush the area around it.
-
Restart and self-check
Power off the printer and the oven, wait 30 seconds and power on. Then run Maintenance > Device self-check > Start on the printer panel and follow the prompts. If the self-check fails, text us what it reports.
-
Run alignment calibration
Tap the temperature icon, then Alignment calibration > Start up. Remove the short piece the printer cuts off, tap Feed slowly until the film holes meet the dark grey marker on the right, then tap Continuous. Overshoot and you must reset and start again.
After switching the oven off, wait until the printer's screen drops the oven icon before you switch it back on. Powering it back too soon is a known cause of Misalignment.
Printer doesn't recognize the oven
-
Confirm the oven is powered
The power switch light should be on, and the sensor inside should glow blue. If either is off, skip to the next section.
-
Try another data cable
The link is an RJ11 6-conductor (6-pin) cable. Swap in a known good one. If the printer then shows the combined printer and oven icon, the original cable is bad and we can arrange a replacement.
-
Still not recognized
The next checks involve opening the printer and the oven to test the internal wiring and boards. Don't open them yourself. Text us at (562) 609-4996 and we will walk through it with you.
Oven won't power on
-
Check the power switch light
If the rocker switch on the back is dark, swap the oven's power cord with the printer's to rule out the cord (then switch them back).
-
Check the fuse
If the cord is fine, the fuse in the power switch has likely blown. With the oven unplugged, gently pry open the fuse compartment next to the switch with a flathead screwdriver and fit the spare fuse kept in the compartment. Power on to test.
-
Switch lit but still no blue light
Power is getting in, but the internal power supply or main board may have failed. Those checks are done with the casing off and live voltage inside, so stop here and contact us with your serial number (on the label at the upper left of the rear panel).
When you contact us, a short video of the error and the oven serial number speed things up. xTool may also ask for logs: in xTool Studio, open the three dots next to the device, then Device settings > Basic info > Export log, and zip the folder.
Watch xTool's video: PET film not feeding into the oven
More videos
Embedded from the manufacturer's official channel.
Common questions
What does the Misalignment error mean?
The film hand-off between the printer and the oven failed, or the printer was not seated on the oven correctly. Film, sensor dust and calibration cause most cases.
Can I use any phone cable as the data cable?
xTool specifies an RJ11 6-conductor (6-pin) cable. Use the supplied one, or a matching replacement.
Where is the spare fuse?
xTool says it is kept in the fuse compartment next to the power switch on the back of the oven.
Where is the serial number?
On a label at the upper left of the oven's rear panel.
- Troubleshoot "Misalignment" Error on xTool Apparel Printer and OS1
- xTool Apparel Printer and OS1 Troubleshooting: Printer Cannot Recognize the Oven
- xTool Apparel Printer and OS1 Troubleshooting: Oven Fails to Power On
- Essential Troubleshooting Information for xTool OS1
- xTool OS1 Shaker Oven FAQs
- Set up xTool OS1 in xTool Studio











































































