Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
xTool OS1 setup: mounting the Apparel Printer, adding powder, preheating and alignment calibration
Lock the OS1's four foot cups, lift the printer on with two people, screw them together, add powder through the slot, connect the purifier, data cable and power, then connect xTool Studio. Before every session, preheat from the temperature icon on the printer panel and wait for the Stable icon. Run Alignment calibration when you first mount the printer, feeding slowly until the film holes meet the dark grey marker.
This is the order xTool uses to set up an OS1 with an xTool Apparel Printer. Do it with two people: the printer has to be lifted onto the oven.
Install the oven and the printer
-
Place the oven and lock the foot cups
Leave at least 1 m (40 in) behind the oven and 90 cm (35 in) on both sides. Once it is in place, use the spanner to loosen the lower nut on each foot cup, screw each foot cup down by hand until it touches the floor, keep going until the wheels lift off, then tighten the upper nut. Do all four. A loose foot cup is the usual reason the printer wobbles during a job.
-
Set the printer on the oven
Remove the printer's output tray and unplug the printer. Two adults lift it, keeping it level so ink does not spill. Line up the printer's delivery slot with the connection slot on the OS1 and set it down.
-
Screw them together
Open the printer lid and install the two supplied M5 screws in the holes, then tighten them.
-
Add powder
Lift off the magnetic cover. Pour the powder evenly into the powder bin through the slot, one pack at a time, not onto the platform. Wipe up any powder on the platform without letting it fall into the side slots, then refit the cover. Never fill past the red line inside the chamber, which marks 2 kg.
-
Fit the output tray
Fold the tray, turn it over, open the two stands underneath and hook it onto the oven.
-
Connect the air purifier
Fit the adapter to the exhaust pipe, stretch the pipe out fully, and connect one end to the purifier and the other to the oven. A fully extended pipe keeps heat from building up and deforming it. On the xTool SafetyPro AP2, use Auto mode or Level 2. A third-party purifier must move 120 m³/h and have filters rated for glycerol and VOCs.
-
Connect data and power
Plug the data cable into the printer and into the data port on the oven, then turn on the OS1 power switch. Leave the printer powered on as well; xTool asks you not to cut its power. Connect the printer to the computer with USB.
-
Connect the software
Install xTool Studio from s.xtool.com/software, click + New project and connect the printer. A green dot on the oven icon means the oven is recognized. On first connection the software runs camera calibration, nozzle detection and print head calibration. Keep the lid closed and the software connected until it finishes.
Preheat before every session
On the printer's panel, tap the Current heating temperature icon at the bottom of the screen, find Preheat and tap Start up. A Heating icon means the temperature is still climbing. Wait for Stable, which xTool defines as a swing of 2°C or less, before you print. Skipping this is a common cause of soft or powdery transfers.
Run the alignment calibration
Do this when you first put the printer on the oven, and again if you get a Misalignment error.
-
Start it
Tap the temperature icon, find Alignment calibration and tap Start up. The printer first cuts off a short piece of film. Take that piece out.
-
Feed slowly
Tap Feed in small steps and watch the film. Stop when the film holes line up with the dark grey marker on the right side inside the oven.
-
Confirm
Tap Continuous to save. If the film goes past the marker you cannot back it up: reset and start the calibration again.
Turning the oven off and on: after you cut the oven's power, wait until the printer screen shows only the printer icon (the oven icon has gone) before you switch the oven back on. Skipping that wait can cause a Misalignment error.
Handy panel shortcuts, all under the temperature icon: Feed control > Feed or Eject to move film, Powder circulation > Start up, and the working temperature setting itself. If anything in setup does not go to plan, text us a photo or short video at (562) 609-4996.
Watch xTool's video: OS1 unboxing and first use
More videos
Embedded from the manufacturer's official channel.
Common questions
The printer shakes during a job. What is wrong?
Usually the foot cups. Lower all four until the wheels are off the floor, then lock the lower and upper nuts with the spanner.
I overshot the dark grey marker during alignment calibration. Can I reverse the film?
No. Reset and run the calibration again, feeding in smaller taps.
How long does preheating take?
xTool does not give a fixed time. Wait until the Heating icon changes to Stable.
Can I use my own air purifier?
xTool allows it only if it moves 120 m³/h and its filters are rated for glycerol and VOCs.
How do I move the oven later?
Raise the foot cups so it rests on its wheels, move it, then lower and lock them again.











































































