Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
BBC Forced Air and Aeolus dryer assembly: fitting the conveyor ends, splicing the belt, power and controls
Attach the drive and take-up assemblies to the oven chamber with the supplied 5/16 in bolts, then feed the belt through and rejoin it with its splice pin, lining up the edge guide exactly so it rides in the roller groove. Tension the belt only enough to stop slipping. Neither dryer has a cord: a certified electrician connects it to a dedicated disconnect with a proper ground.
Both dryers ship crated with the conveyor ends separate. Check every part against the packing list first and report anything missing right away. You need an assistant for the belt. Don't connect power until the end.
Forced Air dryer: assemble
-
Drive assembly
This is the end with the 4 in roller and drive motor. Fit its conveyor rails inside the rails sticking out of the oven chamber and attach it with six of the 5/16 in bolts. Route the plug through the holes in the red cross-member and push it fully into the socket on the heater frame.
-
Take-up assembly
This end has the roller in sliding bearings. Fit its rails the same way and attach it with six bolts.
-
Belt
Loosen, but don't remove, the bolts on the take-up bearings. Pull the splice pin out of the belt without bending it. Feed the belt through the chamber, around an end roller and back through the lower chamber. The rubber edge guide must ride in the groove on the drum roller.
-
Splice
Bring the ends together. Lay a straightedge along the edge guide so both ends line up exactly as you mesh the teeth: one tooth off and the belt can jump out of the groove. While your helper holds the ends, push the pin back in, using needle-nose pliers for the last inch.
-
Tension
At the take-up end, pull the roller drum by hand to take up slack and tighten the bearing bolts. Don't overdo it: too tight damages the splice over time.
Aeolus: assemble
-
Prepare the brackets
Remove the steel shipping brackets at the base of each leg, keeping the black 5/16-18 bolts for the legs. Remove the twelve black 5/16-18 bolts in the connection brackets (three per bracket) and keep them.
-
Fit the conveyor ends
Slide the take-up assembly over the entrance connection bracket until the holes line up, refit the bolts, level it and tighten. Do the same with the drive assembly on the exit side, if it isn't already fitted. Plug the motor cord and the blue sensor cord into their receptacles: cord 1 into 1, cord 2 into 2.
-
Lay the belt
Remove the splice pin with needle-nose pliers without bending it. Lay the mesh belt product side up, with its belt guide on the same side as the double discs on the rollers. It must run on top of both the top and bottom rows of cross members. A 2x4 pushed through the oven helps slide it.
-
Splice
Make sure the belt guide lines up exactly across the joint; try both ways of meshing the teeth to find the right one. While a helper holds the teeth together, push the pin in until it is flush at both ends. Seat the belt guide between the two discs on each roller.
-
Air dams and tension
Fit the two air dams inside the belt over the top cross members: one over the first cross-member at the entrance, the notched one at the tunnel exit. At the entrance, loosen each bearing plate bolt, pull the plate on the disc end by hand and tighten, then set the other end to the same distance. Tension only enough to stop slipping.
-
Curtain
Hook the curtain's tabs into the slots at the entrance at the height you want.
Power
Neither dryer comes with a cord. A certified electrician connects it to a dedicated disconnect with branch circuit protection and a proper earth ground, following the power label on your dryer. Some Aeolus models run on single or three phase and ship with two jumper sets: the electrician fits only the set that matches your supply. On the Forced Air dryer, re-tighten the supply terminal set screws after the first week, then monthly until they stay tight.
Aeolus controls at a glance
| Control | What it does |
|---|---|
| Power disconnect | Cuts all power. The panel door only opens when it is off |
| Start | Powers heaters, conveyor, blowers and panel fans |
| Shut-Down | Heaters off at once; conveyor, blowers and fans run 10 more minutes to cool |
| E-stop | Stops everything; heaters stay hot. Twist counterclockwise to reset |
| Conveyor run switch | Suspend stops the belt. Don't suspend it with heat on |
| Drive motor breaker | Trips if the motor is overloaded. Contact us if it trips |
On the Forced Air dryer, if the belt or blower stops, check the push-to-reset fuse on the back of the control panel. For temperature settings and heat problems, see our BBC settings and troubleshooting guide. Text us a photo or short video at (562) 609-4996 if the belt won't stay in its groove.
Common questions
The belt keeps jumping out of the groove.
The splice is probably one tooth off. BBC says to line up the edge guide with a straightedge when you mesh the teeth. Re-splice it, or text us a photo of the joint.
How tight should the belt be?
Only tight enough to stop it slipping. BBC warns that overtightening damages the belt and splice over time.
Can I wire it myself?
BBC says a certified electrician must connect it to a dedicated disconnect with branch protection and a proper earth ground, under local code.
Which Aeolus jumpers do I use?
The two three-pole jumpers are for single phase and the three two-pole jumpers for three phase. Only one set is used. Your electrician fits the set that matches your supply and the dryer's power label.
What does Shut-Down do on the Aeolus?
It turns the heaters off immediately and keeps the conveyor, blowers and fans running for 10 more minutes so the heaters cool without damaging the belt.
- BBC Industries Forced Air Dryer assembly and operating instructions, doc 16-470
- BBC Industries Aeolus combination infrared and forced air dryer instructions
- AA support requests about BBC and Aeolus dryers, 2024 to 2026










































































