Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Heat press uneven pressure: faded corners, light spots and edges that peel
When one area of a transfer is lighter or peels while the rest is fine, the cause is almost always contact pressure, not a cold spot in the heater. Check for seams, collars and zippers under the platen, a worn or cracked silicone pad, a clamp that no longer locks firmly, and on dual presses a heat plate that isn't parallel to the lower platen. Fix those before you change temperature.
Match your symptom
| What you see | Most likely cause | Go to |
|---|---|---|
| Light band near a collar, seam or zipper | Bulky item holding the platen off the design | Step 1 |
| Same spot fails on every shirt | Worn or damaged silicone pad | Step 2 |
| One side or corner always light (dual press) | Heat plate not parallel to the lower platen | Step 3 |
| Press closes easily, soft clamp, results getting worse | Worn clamp linkage or pressure too low | Step 4 |
| Problems only on a small or specialty platen | Pressure not scaled for the platen | Step 5 |
Step by step
-
Clear the pressing area
Keep collars, cuffs, zippers, buttons and heavy seams off the lower platen. Pull the garment over the platen so they hang off the edge. When you press the second side of a shirt, drape the printed side under the platen so it isn't reheated.
-
Inspect the silicone pad
Lift or slide out the lower platen and look at the pad. If it is dried out, cracked, or has chunks missing, replace it. A pad in that condition gives inconsistent, poor transfers no matter what settings you use.
-
Check that the heat plate is parallel (Maxima and Proxima)
With the press cold and off, use a ruler to measure the gap between the heat plate and the lower platen at all four sides. If the gaps aren't the same, the Maxima manual says to adjust the nut in the center of the heating plate. Re-measure after each small adjustment, and do this for both lower platens.
-
Check the clamp and pressure
A manual press must lock with a firm clamp. On a Geo Knight, worn clamp pins or stretched holes eventually stop the press locking properly, which hurts results badly. Geo Knight sells replacement clamps; contact us to order. If the clamp binds instead, loosen the bolts holding the clamps so the press can re-center, then clean and re-lubricate the linkage pins and platen posts with a clear high-temperature lubricant. Then set pressure as described in our pressure guide.
-
Scale pressure for smaller platens
Smaller platens multiply pressure. Hotronix's guide, for example, cuts the setting by about half on an 11 x 15 platen and by three quarters on an 8 x 10. Make sure quick-change platens are fully seated and locked.
Still uneven?
Measure the platen temperature at the center with a surface probe to rule out a calibration problem (see our temperature guide). If the press checks out and results are still uneven, Text us a photo or short video at (562) 609-4996 of the transfer and the press.
Common questions
Could my heater have a cold spot?
Geo Knight explains that its platens use a single heater coil, so a coil failure shows up as a cold platen or one that runs away hot, not as cool patches. Every platen does read a little different at the edges than the center, which is normal.
Should I just turn the pressure up?
Only after you've ruled out the causes here. More pressure on a press with a worn pad or a seam under the platen just moves the problem, and too much pressure can scorch fabric or damage the press.
How often should the silicone pad be replaced?
There's no fixed interval. Replace it when it feels dried out, has cracks, or has chunks missing. A damaged pad gives inconsistent transfers.
My transfers come out uneven only on the small platen.
Small platens concentrate pressure. Lower the pressure setting for the smaller platen and make sure it's seated and locked properly.
- Geo Knight: Digital Knight pyrometer and temperature offset
- Geo Knight DK20S manual
- Hotronix Perfect Pressure Guide
- Maxima Semi-Auto Dual Heat Press user manual
- AA support requests about uneven heat press results, 2024 to 2026











































































