Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Geo Knight DC16 Digital Combo setup: bench, power cord, pressure knob, bar graph and first press
Put the DC16 on a firm bench 25 to 30 in high, plug the cord into the inlet under the head and tie it to the back post so it never pulls when you swing the head. On the DC16, clockwise on the knob increases pressure and counterclockwise decreases it. Aim for 4 to 6 on the bar graph for most work, and make sure the press locks with a firm clamp.
These steps come from Geo Knight's DC16 Digital Combo manual. The controller works the same way on the air-operated DC16AP, but the manual doesn't cover the DC16AP's air supply, so check with us before connecting a compressor.
Set up the press
-
Bench
Use a firm, sturdy surface about 25 to 30 in high. Higher makes the press harder to close and lock. Bolting through the rear holes in the base is recommended but not required. Geo Knight's universal stand on locking casters also fits the DC16.
-
Power cord
The modular cord plugs into an inlet under the top head. Geo Knight strongly recommends strapping the cord to the white back post. Swing the head back and forth and check the cord moves freely with no tug on the inlet, and that the heater can never press on it.
-
Idle position
When you're not pressing, swing the head over the table but leave the platen up and unclamped. Don't let the platen rest on the pad while it heats.
Set temperature and time
Press TEMP, set the flashing number with the arrows and press TEMP again. Set the time with the arrow keys only. READY appears when the platen is within 5 degrees of the setting. Presets, the prepress timer and the user menus are the same Digital Knight controller as the DK20S: see Digital Knight presets, prepress and user menus.
Set pressure
-
Know the direction
Turn the black knob clockwise to increase pressure (the head comes down) and counterclockwise to decrease it.
-
Lock it
Lower the head and clamp it with a firm two-handed push until you hear the "ka-thunk". The press must lock, not just rest on the item.
-
Read the bar graph
The 0 to 9 bar graph refreshes only when the press is closed, locked and timing. Geo Knight's guide: 0 to 3 is light, 4 to 6 is a good medium for most jobs, 7 to 9 is heavy. A thicker item reads higher at the same knob setting.
First press
-
Prepress the garment
Press the shirt for 2 to 4 seconds to flatten it and drive out moisture.
-
Lay it out
Keep collars, cuffs and zippers off the table. For a second side, pull the shirt over the table so the printed side hangs below.
-
Press
Place the transfer face down on the garment, swing the head over, clamp, and let the timer run. Use your transfer supplier's time and temperature. Geo Knight's chart is only a general reference.
The platen surface is hot enough to burn instantly. Use the handle to swing the head, and keep the cord clear of the platen.
If the press won't heat or shows Err, see heat press won't turn on or heat. For anything else, Text us a photo or short video at (562) 609-4996.
Watch Geo Knight's video: Digital Knight control and instructions
Embedded from the manufacturer's official channel.
Common questions
Which way do I turn the knob for more pressure?
On the DC16, clockwise (to the right). The head lowers toward the table. This is the opposite of Geo Knight's DK clamshells.
The bar graph didn't change after I adjusted the knob.
It updates only once the press is closed, locked and the timer is counting.
Should the head sit over the table or to the side when idle?
Geo Knight says to swing the head over the table when not in use, but keep the platen up and unclamped, never resting on the pad while it heats.
How do I set up air on the DC16AP?
Geo Knight's DC16 manual doesn't cover the air system. Text us before connecting a compressor and we'll walk you through it.
- Geo Knight DC16 Digital Combo manual
- Digital Knight pressure bar graph support
- Geo Knight 2026 catalog
- AA support requests about Geo Knight presses, 2024 to 2026











































































