Support
Machine type
Brand
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses

Heat press cleaning: burned transfer on the platen, PTFE cover sheets and platen covers

✓ Reviewed by Jason KimUpdated 2 min readFits: Prisma Auto · Prisma Dual · Maxima and Proxima · Hotronix · Geo Knight
Short answer

Let the press cool and unplug it, then scrub the heat platen with a non-abrasive detergent or cleaner. Never use an abrasive scrubber or anything that scratches the non-stick coating. To stop it happening again, check the transfer is face down, use a PTFE cover sheet between the platen and the design, and consider fitted PTFE platen covers, which wipe clean with a damp cloth.

Heat platens on most presses have a non-stick coating. It is what lets a stray bit of adhesive peel off, and it is easy to ruin with the wrong cleaner. The most common reason for a dirty platen is a transfer pressed upside down, which melts ink and adhesive straight onto the heat platen.

Clean a burned or sticky platen

  1. Cool down and unplug

    Turn the press off, let the heat platen cool fully, and unplug it. Hotronix requires the power cord to be disconnected before cleaning.

  2. Scrub gently

    Use a non-abrasive detergent or cleaner and scrub the platen surface thoroughly. Don't use steel wool, scouring pads or anything that scratches the coating.

  3. Stubborn residue

    Geo Knight sells a heater block cleaner for residue that won't come off. For other brands, text us a photo before trying anything stronger.

  4. Check the lower pad

    Look at the silicone pad on the lower platen too. Pads wear out over time and can be replaced.

Keep the platen clean

  • Check the transfer faces down against the garment before you close the press. An upside-down transfer seals the image to the heat platen instead of the shirt.
  • Use a cover sheet. A PTFE cover sheet goes between the heat platen and the design, so adhesive or debris can't melt onto the platen. Hotronix notes it gives a smooth, semi-gloss finish on graphics.
  • Fitted platen covers. A lower cover fits over the lower platen like an ironing board cover, protecting the silicone pad and making garments slide on and off easily. An upper cover protects the heat platen from residue, steam and chemical buildup, which is why DTG and sublimation shops like them.
  • Keep the platen up while heating. Geo Knight says not to leave the heat platen resting on the pad while the press heats or sits idle.
  • Keep bulky parts off the table. Collars, cuffs and zippers on the lower platen spoil pressing and shorten the life of the silicone pad.

Choosing a cover for DTF transfers

DTF Station lists PTFE (Teflon), cotton, polyester, canvas or parchment paper as covers for pressing DTF transfers. For the optional second press after peeling, a PTFE sheet leaves more shine. If you want a matte, softer finish, DTF Station suggests covering with a garment or silicone-treated paper instead. For temperatures and times, see DTF heat press settings.

Caring for PTFE sheets and covers

Wipe fitted PTFE platen covers with a damp cloth to remove residue. Keep cover sheets flat and clean, because anything stuck to them will transfer to the next shirt. Replace a sheet or cover once it is torn, creased hard or won't come clean. If a fitted cover doesn't sit right on your platen or leaves marks, Text us a photo or short video at (562) 609-4996.

Watch STAHLS' video: Tips to maintain your heat press

More videos

Protecting the heater with an upper platen cover

Embedded from the manufacturer's official channel.

Common questions

Can I use a scouring pad on a burned platen?

No. Geo Knight says not to use an abrasive scrubber or any pad that will scratch the platen's non-stick coating. Use a non-abrasive cleaner and patience.

Does a fitted upper platen cover replace a cover sheet?

No. Hotronix says the upper cover protects the platen from residue but doesn't replace the need for a non-stick cover sheet.

How do I clean a PTFE platen cover?

Wipe it with a damp cloth to remove residue or buildup.

Should I use a Teflon sheet for the second press on DTF?

For a glossier finish a PTFE sheet is fine. For a matte finish on the second press, DTF Station suggests covering with a garment or silicone-treated paper instead.

My fitted cover leaves a line on shirts. What now?

Text us a photo of the cover on the press and a pressed shirt so we can check the fit and size.

Sources
Did this fix it?