Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Hotronix Auto Open Clam and Hover setup: packaging bolt, power, temperature, two timers and pressure readout
Remove the packaging bolt on top of the press before you switch it on, and plug it into a grounded outlet on a full 20 amp circuit (120 V). Press Mode Select once to set temperature (176 to 430°F), a second time for Time 1, a third time for Time 2, and a fourth time to go back to the operating screen. Set pressure with the knob until the readout shows 1 to 3 (light), 4 to 7 (medium) or 8 to 9 (heavy) with the handle locked down.
Before you switch it on
-
Remove the packaging bolt
There is a packaging bolt on top of the press. Hotronix says to remove it before turning on or operating the press.
-
Pick the spot
Use a sturdy stand at least 36 x 24 inches and 29 inches high. Keep the work area clear.
-
Use the right circuit
120 V presses need a full 20 amp grounded circuit; 220 V presses need a full 10 amp grounded circuit. Don't use a circuit under 10 amps or one shared with other high-demand equipment, especially another heat press. If you need an extension cord, keep it as short as possible and no lighter than 12 gauge.
-
Switch on
The power switch is on the side of the press. Turn it ON and let the press heat.
Hotronix lists what an undersized or shared circuit causes: erratic controller behavior, inaccurate displays, slow heat-up and a tripping circuit breaker. Rule that out first before suspecting the press.
Set temperature and time with Mode Select
Everything is set with the Mode Select button in the center of the control panel and the + and - buttons.
| Press Mode Select | Lights on | What you set |
|---|---|---|
| Once | SET and TEMP | Temperature, 176 to 430°F (79 to 220°C) |
| Twice | SET and TIME | Time 1 |
| Three times | All three | Time 2 |
| Four times | None | Back to the operating (print) mode |
The press has two timers for two-hit applications. For a normal single press, set Time 1 and Time 2 to the same value. The display shows your changes as you make them.
Set pressure and read the readout
-
Turn the knob
Turn the pressure knob clockwise to increase pressure and counterclockwise to decrease it.
-
Lock the handle down to read it
With the handle locked in the print position, the lower right of the display shows a number from 0 to 9. 0 is no pressure and 9 is very heavy.
-
Allow for the garment
Set pressure with the garment you're pressing in place. A thicker item reads higher at the same knob setting.
| Readout | Pressure |
|---|---|
| 1 to 3 | Light |
| 4 to 7 | Medium |
| 8 to 9 | Heavy |
Hotronix: structural damage caused by excessive pressure is not covered under the limited warranty. More pressure is not better. Use what the transfer instructions call for. See how to set heat press pressure.
Your first press
-
Wait for temperature
Let the press reach the set temperature.
-
Load
Position the garment and the transfer on the lower platen.
-
Lower and lock
Lower the platen and lock the handle. The timer starts on its own.
-
Let it open
When the timer finishes, the press releases and the gas shocks lift the platen to the UP position. Keep your face and hands clear as it opens, then peel as your transfer instructions say.
Auto Sleep
After two hours without use the press goes into an energy-saving sleep mode. Press any button on the display and wait for it to return to the set temperature before pressing again.
If it won't open by itself, see auto-open heat press not opening. If the knob spins loose or the press won't power on, Text us a photo or short video at (562) 609-4996.
Watch Stahls' TV: Auto Open Clam, adjusting time and temperature
More videos
Embedded from the manufacturer's official channel.
Common questions
Why are there two time settings?
For two-hit applications. Hotronix says that for a single-hit application you simply set Time 1 and Time 2 to the same value.
What temperature range can I set?
176°F (79°C) to 430°F (220°C).
The display went dark and the press cooled down. Is it broken?
Probably not. After two hours without use the press goes into Auto Sleep. Press any button on the display and let it heat back up to the set temperature.
Which way do I turn the knob for more pressure?
Clockwise increases pressure, counterclockwise decreases it.
Can I just turn the pressure all the way up?
No. Hotronix warns that structural damage caused by excessive pressure isn't covered by the limited warranty. Use the pressure your transfer calls for.
- Hotronix Auto Open Series Clam and Hover Press operator's manual (REV 1122)
- Hotronix heat press manuals and support
- AA support requests about Hotronix Auto Clam presses, 2024 to 2026











































































