Support
Machine type
Brand
Siser Romeo vinyl cutter

Siser Romeo print and cut with Leonardo Design Studio: registration marks, camera alignment and cut contours

✓ Reviewed by Jason KimUpdated 3 min readFits: Siser Romeo 24"
Short answer

In Leonardo Design Studio, check "Print and Cut job" on the art board, build a cut contour with registration marks, and print the Print Artwork layer. Load the print with the mark that has the small square at the bottom left, test cut on a blank area, then move the head over that bottom-left mark and send the Cutting Contours layer with Mirror unchecked. Romeo's camera finds the marks and cuts.

How print and cut works on Romeo

You print your design with registration marks on any printer, load the print into Romeo, and Romeo's built-in camera finds the marks and cuts around the artwork. Because it is a camera rather than a light sensor, Siser says it can read marks on glossy, metallic, glitter and iridescent materials, as well as stickers, magnets and cardstock.

Match your symptom

What you see Most likely cause Go to
Romeo beeps and won't start cutting Camera can't find the first mark Step 7
Cut is mirrored or flipped Mirror was left on Step 7
Thin white edge around the print No contour bleed Step 2
Cut too deep or too shallow Force not tested for this material Step 6
Marks missing after duplicating Page marks off Step 3

Step by step

  1. Set up the art board

    In Leonardo Design Studio's Art Board | Cutting Mat properties, choose a mat, or click Material Roll to work without one (Siser skips the mat for large prints). Check Print and Cut job and pick your paper size from the list. For a size that isn't listed, click the printer icon next to the list and choose it there.

  2. Build the cut contour

    Import a JPG, PNG, TIF or SVG as a print and cut project. In Create Cut Contours, use the mask tolerance slider (and the advanced masking tools if the background isn't fully removed), smooth the contour, and choose whether to keep holes. On the last screen set the offset and turn on Contour Bleed to avoid a thin white edge. Click Finished. For a vector design, select it, click Build Contours, choose Print and Cut Logo and click Apply. The registration marks appear and resize with the artwork.

  3. Duplicate if you need several

    Hold Alt (Option on a Mac) and drag to copy a design; add Shift to keep it lined up. If the marks no longer fit after duplicating, check Page Marks in the Art Board properties.

  4. Print

    Select the artwork, click Send Design, then Send. With the Print Artwork layer selected, choose your printer and click Send to Printer. Load your print material (Siser's example uses EasyColor DTV) before printing.

  5. Load the print

    Place the print behind the pinch rollers with the registration mark that has the small square at the bottom left. Press the down arrow on the touch screen to engage the rollers and feed it in.

  6. Test cut on a blank area

    Feed to a blank part of the sheet. In Cut Settings, Siser's starting point for EasyColor DTV is force 5 to 10 and speed 10. Run a test cut, adjust and repeat until it cuts cleanly. Other materials need their own test.

  7. Position the head and cut

    Use the touch screen arrows to bring the bottom-left registration mark under the blade holder. In Leonardo, select the Cutting Contours layer, check Use Cutter's Settings, make sure Mirror is unchecked, and click Send to Cutter. The camera finds the first mark, scans the others and cuts. If it beeps because it can't read a mark, move the plus symbol onto the mark with the arrows or touch screen; the camera uses that spot for its next scan.

  8. Unload and finish

    Unload with the touch screen arrows, weed, and apply transfer mask if your material needs it (Siser uses TTD Easy Mask with EasyColor DTV).

The camera menu on Romeo also has a registration snapshot (a crosshair preview) and a camera light brightness setting, which help when marks are hard to see. If cuts are consistently offset from the print, Siser's calibration video on this page shows how to calibrate the camera and blade. Still off? Text us a photo of the result at (562) 609-4996.

Watch Siser's video: print and cut with Leonardo Design Studio

More videos

The best way to calibrate your Romeo or Juliet

Embedded from the manufacturer's official channel.

Common questions

Which way does the print go in?

Load it behind the pinch rollers with the registration mark that has the small square at the bottom left.

Romeo beeps and won't find the marks. What now?

Move the plus symbol onto the mark with the arrows or touch screen. The camera uses that position for its next scan.

Can Romeo read marks on glitter or metallic material?

Siser says yes. Romeo uses a camera, so it can read marks on shiny, metallic, glitter and iridescent materials.

Do I need a mat?

Not for large print and cut jobs on roll material. Siser loads them matless.

Why is there a thin white edge around my stickers?

Turn on Contour Bleed when you create the cut contour so the print extends past the cut line.

Did this fix it?