Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex EconoRed troubleshooting: no heat, temperature swings, belt stopped and controller error codes (SbEr, AtEr)
Start with the pilot lights. The green control output light and red relay light should cycle together, and each heater has a white light. No power light means a power supply, breaker or fuse problem; a power light but no heat points to fuses, the heater or a relay. SbEr on the controller means the Type J sensor has failed: the controller drops into manual mode so you can keep running while a replacement is ordered.
Turn off and lock out power at the main disconnect before opening the control box. The red power light must be off. Any test with power on must be done by a qualified electrician. Shutting off the front power switch alone does not make the box safe.
Read the lights first
| Light | What it tells you |
|---|---|
| Red power | Main power switch is on |
| Green output | Controller is calling for heat. Should cycle on and off. |
| Red relay | Relay is sending power. Should cycle with the green light. |
| White heater | One per heater. Power is reaching that heater. |
| Blue fan | One per fan. Power is reaching the exhaust fan. |
Match your symptom
| Symptom | What to check |
|---|---|
| No heat, power light off | Incoming power, the shop disconnect, breakers and fuses, the power cord and its connections |
| No heat, power light on | A burned out heater, the system fuses in the control box, and which pilot lights are on |
| Too hot or too cold | Pilot lights: a relay can stick on or off |
| Temperature swings | Sensor position, clean sensor connections, drafts or fans in the shop |
| Belt stopped or erratic | Motor plug, sprocket and chain, obstructions in the belt path, belt tension |
Fuses and relays are inside the control box, so those checks are for an electrician. The chain, belt path and tension you can check yourself with power off; see our maintenance guide.
Controller error codes
| Code | Meaning | What to do |
|---|---|---|
| SbEr | Sensor break | Replace the Type J sensor. Run in manual mode meanwhile. |
| LLEr, HLEr | Reading outside the low or high range setting | Contact us. The range values need resetting. |
| AHEr | Analog module damage | Module or controller replacement. Look for voltage spikes. |
| AtEr | Auto tune failed | Repeat the auto tune. If it fails again, contact us. |
| oPEr | Manual mode not allowed | Contact us |
| C5Er | Memory values changed | Contact us to reconfigure the settings |
Run in manual mode after SbEr
When the sensor fails, the display shows SbEr, the output indicator flashes MAN and H0.00 appears below. Use the up or down arrow to set the percentage of time the heaters are on (80.0 means on 80% of the time). You can keep producing like this, checking your ink temperature closely, until the new sensor is in.
Auto tune
Do this if your shop is below 240 V, or after a new controller, sensor or heaters. Start with the heaters below 300°F. Enter the set point first: 700°F for 240 V class units (500°F for 120 V units).
-
Open auto tune
Hold the scroll button until A-T shows, then release.
-
Start it
Hold scroll again until the output indicator flashes TUNE, then release. PASS appears; press scroll once to clear it.
-
Wait
TUNE keeps flashing until the process ends. It can take up to 30 minutes.
If the dryer smells hot, smokes heavily, vibrates or makes new noises, turn it off and contact us. Text a photo of the control panel with the lights on to (562) 609-4996.
Common questions
The belt runs but there's no heat. What first?
Check the heat switch is on and watch the lights. If the green light cycles but the red relay light doesn't, the relay is the suspect. If both cycle but a white heater light stays off, that heater may be out. Internal checks with power on are for a qualified electrician.
What does SbEr mean?
Sensor break. The Type J thermocouple has failed. The controller switches to manual mode; set a percentage of on time with the arrows and keep printing while you get a new sensor.
When do I need to auto tune?
Vastex tunes every dryer at the factory. Auto tune again if your supply is below 240 V (for example 208 V), or after replacing the controller, the sensor or the heaters.
How do I switch between Fahrenheit and Celsius?
Hold the scroll button until SEt shows, press scroll 5 times to reach UNIt, then use the down arrow for °C or the up arrow for °F.
The temperature keeps swinging.
Check the sensor position and connections, and stop drafts or fans blowing through the chamber.
- Vastex EconoRed (ER) Series Dryers: assembly, operating and maintenance instructions, doc 01-32-001E (PDF)
- AA support requests about Vastex dryers not heating, 2024 to 2026










































































