Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Vastex EconoRed cure settings: temperature, heater height, belt speed, exhaust, start-up and shutdown
Start the belt before the heat, and never stop it while the heaters are above 300°F. For plastisol Vastex suggests starting at an 800°F set point, heaters 3 in above the garment, about 30 seconds in the chamber and the exhaust at 25%. The controller reads the heater, not the ink, so check the ink itself reaches 310 to 320°F. At shutdown, turn the heat off and keep the belt running until the dryer drops to 300°F.
Three things control the cure on an EconoRed: the temperature set point, the heater height and the belt speed. Dryers built from June 2024 also have a variable exhaust. Change one at a time and test.
Start-up
-
Main power
Turn the main power switch on the side of the control box to ON. The red power light comes on.
-
Clear the belt
Remove anything from the conveyor and belt.
-
Power switch
Turn on the power switch. The belt speed control and heat switch get power and the exhaust fan starts.
-
Belt
Turn on the conveyor and set your speed.
-
Heat
Turn on the heat switch. Hold the up arrow on the controller to raise the set value; it climbs faster the longer you hold it. Allow about 15 minutes to heat up.
-
Exhaust
Unlock the knob near the stack and slide it to your flow percentage.
The belt must be moving whenever the heaters are above 300°F (149°C).
Starting settings
| Setting | Plastisol | Water-based or discharge |
|---|---|---|
| Ink must reach | 310 to 320°F | Full cure after the water evaporates |
| Set point | 800°F | Lower as time goes up |
| Heater height | About 3 in (2 to 3 in range) | 2 to 3 in |
| Time in chamber | 20 to 30 seconds | 50 to 90 seconds |
| Exhaust | 25% | Enough to clear steam and fumes |
Vastex stresses these are starting points. Garment moisture and color, ink color and thickness, and room conditions all change the result.
Adjusting
- Heater height: turn the crank on top clockwise to raise the heaters, counterclockwise to lower them.
- Belt speed: turn the knob clockwise to speed up. The volt meter shows the volts going to the motor. Your dryer has a label on the control box that converts volts to time in the chamber; always confirm with a stopwatch.
- Exhaust: use just enough to stop smoke escaping at the ends. Too much cools the area under the first and last heaters, and above 50% film and paper can lift.
- Idle time: if nothing runs for over 10 minutes, drop the set point to 500°F.
Check the cure
The sensor reads the heater face, so measure the ink. A contact thermocouple (donut probe) is the most accurate. A heat gun reads cooler than the real ink temperature; if you use one, aim at the ink while it's still under the last heater, near the outside of the print. Wash test new combinations.
Shutdown
-
Heat off
Turn off the heat switch and let the heaters fall to 300°F or lower with the belt still running.
-
Belt off (optional)
Once at 300°F, turn the belt speed down to off, or leave it set for the next shift.
-
Power switch
Turn the power switch off. Only the power light should still be on.
-
Main power
Turn the main power switch OFF at the end of every shift. No lights should be on.
If prints come out under cured even at slow speeds, text us your settings and a photo at (562) 609-4996.
Watch Vastex's video: EconoRed settings to cure plastisol
Embedded from the manufacturer's official channel.
Common questions
Why is my set point so much higher than the cure temperature?
The sensor sits right under the heater, so it reads far hotter than the garment. Vastex has you set it several hundred degrees above the ink cure temperature.
How long does it take to heat up?
About 15 minutes to reach 700 to 800°F.
What's the best way to check cure temperature?
A contact thermocouple such as a donut probe is most accurate. A laser gun reads low; if you use one, aim at the ink while it's still under the last heater, toward the outside of the print.
Film or paper blows around in the chamber.
Turn the exhaust down. Vastex says light items go airborne above about 50%.
Nothing is going through for a while. Should I turn it off?
If it's idle more than 10 minutes, Vastex suggests dropping the set point to 500°F. It takes about 10 minutes to come back up.
- Vastex EconoRed (ER) Series Dryers: assembly, operating and maintenance instructions, doc 01-32-001E (PDF)
- AA support requests about curing on conveyor dryers, 2024 to 2026











































































