Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
BBC Flash-Amatic: installing it on a flash stand and setting the auto swing dwell timer
To install a BBC Flash-Amatic, take off its side cover, fix the shaft collar 4 inches below the top of your flash stand's lower tube, and slide the unit over the tube. Tighten the U-bolt, set the bronze bearing and refit the upper tube and heater. In AUTO, a tap on the foot switch swings the heater 110 degrees, holds it for the timer setting and returns it. Set the timer range to 10S for flash times of 1 to 10 seconds.
The Flash-Amatic (BBC part BFA-009FS) is a motorized base that swings a BBC flash heater over the platen when you tap a foot switch, holds it there for a set time, and swings it back. It fits all BBC flash stand models and takes the guesswork out of flash time.
Install it on your flash stand
Tools: the hex key that comes with it, a 1/2 in wrench and a Phillips screwdriver. Two people are needed if the heater is on the upper tube.
-
Open the side
Remove the six screws and take off the side cover. Loosen the two nuts on the back that hold the U-bolt.
-
Unpack the inside
Cut the cable tie holding the shaft collar, bronze thrust bearing and shipping tube. Throw the shipping tube away.
-
Collar on the lower tube
Lift the upper tube and heater off your flash stand. Fix the shaft collar 4 in below the top of the stand's lower tube and tighten its set screw with the hex key.
-
Fit the unit
Slide the Flash-Amatic down over the lower tube so the tube passes through the notched flange, the U-bolt and the inner bracket hole, and rests on the inner bracket flange. Tighten the U-bolt nuts.
-
Bearing and upper tube
Set the bronze thrust bearing on top of the lower tube, under the upper tube bracket. Take the bent bolt out of your stand's shaft collar, set the collar on the Flash-Amatic's upper tube bracket, and thread the bent bolt through the bracket into the collar a few turns.
-
Heater back on
Push the upper tube through the collar, bracket and bearing into the lower tube. Set the height and tighten the bent bolt. Refit the side cover.
-
Test the swing
Plug in, switch to AUTO and tap the foot switch. Watch the heater swing 110 degrees, dwell and return home. If the heater passes over the Flash-Amatic itself, reposition the heater. Only adjust the heater while it is cold.
Automatic and manual modes
| Mode | What the foot switch does |
|---|---|
| Auto | Tap it: the heater swings 110 degrees clockwise, dwells for the timer setting, then swings home. On 100 V power, hold the switch for 1 second, then release. |
| Manual | Hold it: the heater swings out and back. Lift your foot and it stops wherever it is. |
Setting the dwell timer
The timer has a dial marked 0 to 1 and a small range selector beside it. The range code multiplies the dial:
| Range code | Dwell range |
|---|---|
| 1S | 0.1 to 1 second |
| 10S | 1 to 10 seconds |
| 1M | 0.1 to 1 minute |
| 10M | 1 to 10 minutes |
For flashing, set the range to 10S. BBC's plastisol flash starting point of 5 to 10 seconds then sits between the middle and top of the dial. Test on a spare garment and adjust. The timer also has 1H and 10H ranges, which you won't need for flashing.
Keep hands and bodies out of the swing path. The heater moves on its own in Auto mode, and the heater face stays hot for 10 to 15 minutes after switching off.
The unit has its own circuit breaker on the front panel. If it stops swinging, check that the breaker hasn't tripped and the foot switch is plugged in, then text us a photo or short video at (562) 609-4996.
Common questions
Does the Flash-Amatic fit my flash?
BBC says it works with all BBC flash stand models. It mounts on the stand's lower tube.
How do I set a 6 second flash?
Set the range selector to 10S (1 to 10 seconds across the dial) and turn the dial to the 0.6 mark. Then test and fine-tune on a spare shirt.
The heater swings over the unit. Is that a problem?
Yes. BBC says to reposition the heater so it doesn't travel over the Flash-Amatic. Do it only when the heater is cold.
What is the difference between Auto and Manual?
In Auto, a tap runs a full timed cycle. In Manual, the heater only moves while you hold the pedal and stops when you let go.











































































