Support
Machine type
Brand
BBC Flash Dryers: Black Flash, Afford-A-Flash, Air Flash and Auto Flash

BBC flash dryer assembly and electrical: Black Flash stand, Afford-A-Flash, Air Flash, Auto Flash and outlet requirements

✓ Reviewed by Jason KimUpdated 3 min readFits: Black Flash · Afford-A-Flash · Air Flash · Auto Flash
Short answer

Before you assemble a BBC flash dryer, check the model number against the outlet. Many 18 x 18 inch 120 V models draw 16 to 19 amps, and the BF2-2200, BF3-4500 and LC2200 need their own branch circuit. Build the stand legs and casters first, fit the heater to its bracket face up on a soft surface, then drop the upper tube in, set the collar height and level the heater to the platen. No extension cords, and never modify the plug.

A BBC flash dryer arrives as a heater head plus a stand kit. Most "it won't get hot" calls BBC gets come down to the outlet, so check the electrical section before you plug in.

Electrical: match the outlet to your model

The model number is on the carton and the heater label. Common US Black Flash models:

Model Heater Volts Amps
BF1-1600S 16 x 16 in 120 12.9
BF2-2000S 18 x 18 in 120 16.0
BF2-2200S, HC 18 x 18 in 120 19.0
BF2-2600S 18 x 18 in 240 11.3
BF3-4500S, HC 18 x 24 in 240 18.5
BF4-5200S 24 x 24 in 240 20.6

Afford-A-Flash: LC1600 is 16 x 16 in at 120 V, 12.9 A; LC2200 is 18 x 18 in at 120 V, 19.0 A; LC2700 is 18 x 18 in at 240 V, 11.3 A.

  • The BF2-2200, BF3-4500 and LC2200 must be on a single receptacle on their own branch circuit, with nothing else on it.
  • For the Auto Flash ABF3-2200HC, BBC says to have an electrician provide a dedicated 120 V, 20 A circuit.
  • Use a grounded outlet. All wiring must meet local code.
  • No extension cords. Don't change the cord or plug: it is unsafe and voids the warranty.

Black Flash on a BF12 stand

The BF12-172 standard stand is for 16 and 18 in models (BF1, BF2). The BF12-174 heavy duty stand is for BF3, BF4 and BF5. Tools: two 1/2 in wrenches, a 7/16 in wrench and a Phillips screwdriver. Lay down towels or cardboard first to protect the paint.

  1. Legs

    Take the three screws out of the end of the black lower tube. Screw the first leg on through one hole, with the tube washer sitting in the leg's slot. Screw on the second leg next to it, and bolt the two legs together with two 5/16 in bolts and nuts. Add the third leg with the last screw and bolt it to its neighbor. The last two legs bolt to the others only.

  2. Casters

    Screw the casters (two of them lock) or the optional leveling feet into the insert nuts at the leg ends.

  3. Top bracket

    Lay the heater face up on a smooth surface so the black element face isn't scratched. Bolt the handle to the top bracket, then screw the bracket to the heater with the six #12 screws. Snug them, but don't strip the sheet metal.

  4. Upper tube

    Slide the curved plate on the upper tube between the bracket and the heater, and fix it with two leveling knobs (each with a spacing collar). Thread the third knob into the bracket's insert nut. Put the large collar at least halfway up the upper tube and lock it with the bent bolt.

  5. Join and level

    Drop the upper tube into the lower tube until the collar rests on it. Roll the stand to the press and use the three knobs to set the heater face parallel to the platen.

Afford-A-Flash

  1. Head

    Bolt the handle to the mounting bracket (7/16 in wrench), then bolt the bracket to the upper tube with two 1-3/4 in bolts and nuts. The slotted hole is used to level the head later.

  2. Base

    Put the collar at least halfway up the upper tube and lock it with the bent bolt. On a flat surface, bolt the two legs to the lower tube with the 2-1/2 in bolts, then fit the casters.

  3. Finish

    Drop the upper tube into the lower tube, set the height with the collar, level the heater and tighten the two bracket bolts.

Air Flash

Screw the five leveling feet into the legs, fix the legs to the lower tube with its three screws and the 5/16 in bolts, set the large collar halfway up the upper tube, and attach the heater with the two knobs and small collars. Use the knobs to level the heater parallel to the platen, and put the magnetic handle where it is easy to swing.

Auto Flash

The Auto Flash bolts to the flood bars of an automatic press. Set bolts A in the mounting plate holes for your press brand, move the clamp bolts and dowel pin to the spacing your flood bars need, then turn the clamps 90 degrees, slide the flood bars under, turn them back and tighten.

Text us a photo or short video at (562) 609-4996 if a part is missing or the stand won't sit level.

Common questions

My 120 V flash keeps tripping the breaker. Why?

An 18 x 18 in 120 V model draws 16 to 19 amps. The BF2-2200 and LC2200 must be the only thing on their branch circuit. Have an electrician check the circuit. Don't use an extension cord.

Which stand fits my Black Flash?

BF12-172 for the 16 and 18 inch BF1 and BF2 models, and the heavy duty BF12-174 for BF3, BF4 and BF5.

Can I change the plug to fit my outlet?

No. BBC says modifying the cord or plug is unsafe and voids the warranty. Have the right outlet installed instead.

How do I level the heater?

On the Black Flash and Air Flash, use the leveling knobs on the bracket. On the Afford-A-Flash, use the slotted bracket hole and tighten the two bolts.

Did this fix it?