Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Brown PonyXprs dryer: start-up, cure settings, shutdown, belt tension and belt tracking
Brown's starting point for the Pony dryer is about 60 seconds in the chamber with the heaters on high and set about 3 in above the garment. Always confirm the cure with a stretch test and heat tapes. To shut down, turn the heaters off and let the dryer cool for about 10 minutes before you switch off main power. Track the belt on high speed with the heat off, using the knobs on the end of the conveyor frame.
The control panel
| Control | What it does |
|---|---|
| Main power | Turns the dryer on and off |
| Belt speed | Sets how fast the belt moves through the chamber |
| Pilot light | On when a heater is on |
| Heater switch | One on the PD-2004. Two on the PD-2006 and PD-2407; the right hand switch is the front heater. |
| Breakers | Protect the circuits |
Start-up
-
Main power on
Turn the main power switch on.
-
Set the belt
Adjust the belt speed dial so a garment spends about 60 seconds in the chamber. Time it with a stopwatch.
-
Heaters on
Turn on the heater switch or switches. Brown recommends running them on high for most jobs.
-
Set the height
Use the handles on the ends of the tunnel to raise or lower the heater rack so the heaters sit about 3 in above the garment.
-
Forced air
Turn the forced air switch on if your job needs it.
-
Check the cure
Do a stretch or crack test on every job and check garment temperature with heat tapes.
Brown makes the user responsible for confirming cure. Check prints regularly during production, not just at the start.
Shutdown
-
Heaters off
Turn the heaters off and let the dryer cool for about 10 minutes.
-
Main power off
Then turn the main power off.
Belt tension
The knobs on the ends of the pulley take-up plates set tension. Use just enough that the belt doesn't slip on the pulley. Too much shortens the life of both the belt and the belt motor. All conveyor belts stretch, so check tension periodically.
Belt tracking
-
Heat off, belt fast
Run the belt on high speed with the heaters off and watch which way it drifts.
-
Steer it
Use the knobs on the end of the conveyor frame. Adding tension on one side moves the belt toward the opposite side. Reducing tension on one side moves the belt toward that side. Make small changes and let the belt run a few turns between them.
-
Recheck hot
The belt may need a small correction once the dryer is at full temperature, and again as the belt stretches with wear.
When cure changes
If prints that used to cure start failing a stretch test, check that the heater pilot light is on, that the heater rack has not been moved, and that belt speed has not been changed. Slow the belt or lower the heaters a little and test again, one change at a time. If heat seems low, see our troubleshooting guide.
Drive chain
Check the belt drive chain for lint now and then. If it's heavy, turn off power to the dryer and remove the lint with a stiff brush. If the belt still slips or wanders, text us a short video at (562) 609-4996.
Watch Brown's video: how to set up a PonyXprs
Embedded from the manufacturer's official channel.
Common questions
What settings does Brown recommend?
Belt speed for about 60 seconds in the chamber, heaters on high for most jobs, heaters about 3 in from the garment. Then check the cure.
How tight should the belt be?
Just enough that it doesn't slip on the pulley. Extra tension shortens the life of the belt and the belt motor.
The belt drifts to one side.
More tension on one side pushes the belt toward the other side; less tension on a side lets it move toward that side. Adjust with the dryer cold and the belt on high speed.
Which heater switch is which on the two-heater models?
On the PD-2006 and PD-2407 the right hand switch controls the front heater.
How do I know it's cured?
Brown says to check every job with a stretch or crack test and to check garment temperature with heat tapes.











































































