Machine type
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
Epson SureColor G6070 DTF printer
Mimaki TxF300-1600
Mimaki TxF330-800
STS XPD-924D DTF Printer (Mutoh)
STS VJ-628D DTF Printer (Mutoh)
DTF Station Vega S17
STS XpertJet 1682D (XPJ-1682D) 64 inch DTF Printer
STS XPD-724 DTF Printer (Mutoh)
Hotronix Fusion IQ, Air Fusion IQ and Dual Air Fusion IQ
Geo Knight DK20S and DK20SP Digital Knight Swing-Away Presses
DTF Station Maxima and Proxima Dual Heat Presses
Hotronix Auto Open Clam and Hover Heat Press
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
Insta 718, 728 and 828 Automatic Swing-Away Heat Presses
DTF Station Prisma Sentry Heat Press
Geo Knight DC16 and DC16AP Digital Combo Swing-Away Presses
Geo Knight DK Digital Clamshell Presses: DK20, DK16, DKA Auto, DK8 Label and DK7 Cap
Hotronix Auto Open Cap Press and 360 IQ Hat Press
Hotronix Craft Heat Press 9 x 12
Hotronix Mighty Mug Heat Press
Insta 256 and 288 Manual Swing-Away Heat Presses
Insta 907 Dual Station Shuttle Label Heat Press
Viper MAXX pretreatment machine
Ecofreen Mister-T2 and Mister-T2 Pro pretreatment machines
Pearl Elite and Pearl PTM DTG pretreatment machines
Viper XPT-1000 pretreatment machine
Lawson Silver-Jet and Silver-Jet V2 DTG Pretreat Sprayers
Lawson Zoom-AE DTG pretreatment machine
Viper MINI handheld DTG pretreatment machine
Brand
Prestige XL series (L2, XL2, XL2 Pro, XL3, XL4)
DTF Station Prestige R2 Pro
DTF Station Prestige R1
DTF Station Prestige R2 (original)
Prestige X6
DTF Station Prestige A4
DTF Station Prestige A3+ and A3+ R
DTF Station Aries 124 UV DTF printer
Miro DTF Powder Shakers: Miro 13 Max, 16, 24 and 36
DTF Station Aries 213 and Aries 113 UV DTF printers
Seismo L16R and L24R DTF Powder Shaker and Dryer
Phoenix Air 16x20 DTF Curing Oven
DTF Station Maxima and Proxima Dual Heat Presses
DTF Station Prisma Auto Heat Press
DTF Station Prisma Dual Heat Press
DTF Station Prisma Swing Heat Press
DTF Station Vega S17
DTF Station Prisma Sentry Heat Press
DTF Station Seismo V36R DTF Powder Shaker and Dryer
DTF Station Arc 127 automatic cutter for DTF and UV DTF film
Epson SureColor F2100
Epson SureColor G6070 DTF printer
Epson SureColor F2270
Epson SureColor F3070
Epson SureColor F570
Epson SureColor F170
Epson SureColor F6470 and F6470H
Epson SureColor F6370
Epson SureColor F7200
Epson SureColor P-Series photo printers (P700, P900, P6570, P8570)
Epson SureColor T-Series CAD and technical printers
Epson SureColor S-Series (S40600, S60600, S80600)
Brown PonyXprs and PonyPrinter assembly, leveling, micro registration and off contact
Unpack the PonyXprs, lock the casters, then fit the print heads, clamps, platen support rails, platens and the dryer belt. Use a level only on the first platen. After that, level each print head to that platen with a flat screen, and use the first head to set every other platen parallel. Brown's point: make the machine parallel to itself, not level to the world.
Assembly
-
Uncrate and place it
Remove the machine from the crate or skid, roll it where it will live and lock the casters.
-
Print heads and clamps
Install the print heads, then the screen clamps.
-
Platen support rails
Attach the left and right rails with the supplied 5/16 in bolts, washers and flange nuts.
-
Platens
Set each platen on its leveling rails and secure it with the knobs.
-
Dryer belt
Turn both tension knobs counterclockwise to move the tail pulley in and give enough slack. With the edges even, interlock the splice teeth and push the splice wire all the way through. Turn both knobs clockwise until the belt is snug. Don't overtighten.
-
Power and exhaust
Connect power to suit your dryer model (see the hub page table) and set a fan in a nearby window to pull out curing smoke.
Level the printer
-
First platen
Put a level on one platen. Adjust it with the bolts in the top of the hub, and tighten the platen support rails once it's flat.
-
First head
Clamp a flat screen in a head and pull it down into the registration gate of that platen. Loosen the leveling bolts on the side of the clamp with a 7/16 in wrench, flatten the screen to the platen, and tighten.
-
Other heads
Level each other head to that same first platen.
-
Other platens
Use the first adjusted head to set every other platen parallel to the screen frame, the same way as step 1.
Brown's rule: you are making the machine parallel to itself, not level to the world. A level only helps on the first platen.
Adjusting a screen
| Move | How |
|---|---|
| Front, back, diagonal | Loosen the two knobs on top of the head so the clamp can glide. Loosen the top knob and turn the back knob; the guide shows direction and amount. Retighten the top knob finger tight. |
| Side to side | Loosen one of the knobs at the back of the head and tighten the other. The screen moves toward the loosened knob. Snug them finger tight against each other. |
| Off contact | Loosen the wing nut, turn the top center knob to lift the screen to the height you want, retighten. Relevel if needed. |
| Tilt | Loosen the bolt on the side of the clamp hanger bracket and tilt the clamp flat for your off contact setting. |
Return every micro adjustment to center before starting the next job so you have travel in every direction.
Registration gate
The gate is adjusted at the factory. If it ever needs adjusting, lower the first print head, loosen the 5/16 in nut on the left registration pin, turn the 1/4-20 adjustment bolt on the left side of the gate to move the pin, then tighten the pin nut. If registration still wanders, text us a photo of a test print at (562) 609-4996.
Watch Brown's video: how to set up a PonyXprs
Embedded from the manufacturer's official channel.
Common questions
Do I level every platen with a bubble level?
No. Only the first one. After that, set heads and platens parallel to each other using a flat screen.
How do I move the screen side to side?
Use the two knobs at the back of the head: loosen one, tighten the other, and the screen moves toward the loosened knob. Keep them finger tight.
How do I add off contact?
Loosen the wing nut, turn the knob at the top center of the head until the screen is at the height you want, and tighten the wing nut. Then recheck that the screen is level.
My registration pins seem off.
The registration gate is set at the factory. If it needs adjusting, put head one down, loosen the 5/16 in nut on the left pin and adjust the 1/4-20 bolt on the left side of the gate.
Why did my platens warp?
Standard platens are melamine coated press board and warp with too much heat. Replacements are available.










































































